Problem 1: Highlight the data path that is active during the execution of the following MIPSinstruction. Write the registers that are read from or written to in the data path. Also, explicitly writethe values of MUX control signals.slti $t0, $t1, Oxe5bbReadALU operationregister 1Readdata 1MemWriteReadZeroMemtoRegInstructionregister 2ALUSrcRegisters ReadWriteALUALUresultReadAddress0.Mdatadata 2registerWritedataDataRegWriteWritememorydata1632MemReadSign-extend

Actually , the answer has given below:

Problem 1: Highlight the data path that is active during the execution of the following MIPS instruction. Write the registers that are read from or written to in the data path. Also, explicitly write the values of MUX control signals. slti $t0, $t1, Oxe5bb Read register 1 Read register 2 Registers Read 4| ALU operation Read data 1 | MemWrite MemtoReg Zero Instruction ALUSrc ALU ALU result Read Write register Address data data 2 Write data Data Write data memory RegWrite

Problem 1: Highlight the data path that is active during the execution of the following MIPS instruction. Write the registers that are read from or written to in the data path. Also, explicitly write the values of MUX control signals. slti $t0, $t1, Oxe5bb Read register 1 Read register 2 Registers Read 4| ALU operation Read data 1 | MemWrite MemtoReg Zero Instruction ALUSrc ALU ALU result Read Write register Address data data 2 Write data Data Write data memory RegWrite

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Consider the following code fragment. What are the contents of the eax, ebx and ecx registers after the code fragment has been executed'? Show your work.section .datax:dd32y:dd17section .textmov eax, xmov ebx, [eax]mov ecx, [eax +4]add ebx, [x]add ecx, ebxmov eax, [eax]
The control signal Ep or iEnableoutput allows the program counter to decrement its value. True False The control signal Ep or iEnableoutput sends the content of the program counter to the W bus. True False A tri-state buffer is needed for all data going to the W bus. True False In using 'assign' statement in Verilog, the left hand side must always be a register. True False In declaring a register in Verilog, the following format must be followed: reg [LSB:MSB] identifier; True False
In the Intel 8086 microprocessor, suppose the register AX contains the data 35AB H. What will be the contents of AX after executing the following programs? Assume that the initial content on the Carry Flag (CF) is one for all the calculations. You MUST clearly show ALL your steps in obtaining your final result for getting full and/or partial credit. Please present your final result in Hexadecimal format. (a) MOV CL,04H SHR AX,CL RET (b) MOV CL,04H RCR AX,CL RET
One of these methods will produce less latency of I/O transfers is ___________ a.Program-controlled I/O b.DMA c.Interrupt driven I/O d.Memory mapping
Th is exercise is intended to help you understand the relationship between forwarding, hazard detection, and ISA design. Problems in this exercise refer to the following sequence of instructions, and assume that it is executed on a 5-stage pipelined datapath:add r5,r2,r1lw r3,4(r5)lw r2,0(r2)or r3,r5,r3sw r3,0(r5)> If there is no forwarding or hazard detection, insert nops to ensure correct execution.> Repeat above step, but now use nops only when a hazard cannot be avoided by changing or rearranging these instructions. You can assume register R7 can be used to hold temporary values in your modifi ed code.> If the processor has forwarding, but we forgot to implement the hazard detection unit, what happens when this code executes?
For the following code, explain what the register file and forwarding unit are doing during thefifth cycle of execution. If any comparisons are being made, mention them. Remember, usethe forwarding unit from class, not the book. LOOP:LDUR X1, [X6, #40]ADD X5, X5, X8ADD X6, X6, X8STUR X1, [X5, #20]CBZ X1, LOOP
Consider the following instruction:Instruction: Add Rd, Rs, RtInterperation: Reg[Rd] = Reg[Rs] + Reg[Rt] RegWrite MemRead ALUMux MemWrite ALUOp RegMux Branch a, What are the values of control signals generated by the control in Figure 4.2 for the above instruction? b, Which resources (blocks) perform a useful function for this instruction? c, Which resources (blocks) produce outputs, but their outputs are not used for this instruction? d, which resources (blocks) produce no output for this instruction?
6. Suppose that the interrupt processing method of is to store the breakpoint in the address of 00000Q unit, and fetch the instruction from the 77777Q unit (that is the first instruction of the interrupt service routine) and execute it. Write the micro-operations sequence that completes this function.
Q: Specify the mode byte for DMA channel 2 if it is to transfer data from an input device to a memory buffer starting at address A000H and ending at AFFFH. Ensure that μp is not completely locked off the bus during the DMA cycle. Moreover, at the end of each DMA cycle, the channel is to be reinitialized so that the same buffer is to be filled when the next DMA operation is initiated?
] The following sequence of 16-bit control words are presented to the datapath. For each, identify the microoperation that is executed as an RTL expression. Assume that Memory Write (to the RAM) is NOT asserted unless it is explicitly indicated. (a) x0001 (b) x4251 (c) xFFFE, MW asserted
Assume that the state of the 8088’s registers and memory just prior to the executionof each instruction in problem 15 is as follows: * in photos*What result is produced in the destination operand by executing instructions (a)through (k)? *only h through k* (h) MUL DX(i) IMUL BYTE PTR [BX+SI](j) DIV BYTE PTR [SI]+0030H(k) IDIV BYTE PTR [BX][SI]+0030H
Q:Answer the following sentence with (True) or (False) and correct the false answer: 1. You can input data of size 16-bit through the fixed port. 2. In the maximum mode, the status signals S₁, S₂ and S3 are controlled by the bus controller. 3. HLDA is an output signal. 4. In 8086, when executing the instruction MOV AL, [SI+100D H] where SI-100AH, Ao=0 and BHE=1 5. When S, is 0, the TF is disabled.