Solution plz ASAP respectively. E = 2.1 x 10$ N/mm? and Poisson'sratio u = 0.3. Determine the magnitude of theIn a stressed member, *0%3D30principal stress.446 10"1..eion:3032 10

ε30=455×10-6ε120=-32×10-6using following relations:for…

respectively. E = 2.1 x 10 N/mm? and Poisson's ratio u = 0.3. Determina the magnitude of the inclined at 30° to the known directions of the In a stressed member a drain gauges are fixed such that they are 2.1 x 10$ N/mm? and Poisson's respectively. E 0.3. Determine the magnitude of the ratio u = principal stress.

respectively. E = 2.1 x 10 N/mm? and Poisson's ratio u = 0.3. Determina the magnitude of the inclined at 30° to the known directions of the In a stressed member a drain gauges are fixed such that they are 2.1 x 10$ N/mm? and Poisson's respectively. E 0.3. Determine the magnitude of the ratio u = principal stress.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
Set P1_1 = 58 kN , P2_2 = 33 kN . (Figure 1)
Discuss about Distribution of Bearing Pressure
Determine the normal stress in each of the cables? (MPa) a. 85.7 b. 75.7 c. 65.7 d. 55.7 If the cables elongated by 1 mm, what is the vertical displacement of the precasat slab? (mm) a. 1.758 b. 1.658 c. 1.458 d. 1.558 What is the tensile force in each of the cables? (kN) a. 5.98 b. 4.98 c. 7.98 d. 6.98 SOLVE ALL AND WILL GET A LIKE <3 ps: unit weight of concrete is 24kn/m^3
A planned flexible load area (see Figure P7.2) is to be 3 m x 4.6 m and carries a uniformly distributed load of 180 kN/m2. Estimate the elastic settlement below the center of the loaded area. Assume that Df = 2 m and H = ∞ . Use Eqn 7.4
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft.
The lower ends of the three steel rods are at the samelevel before the force P = 600 kN is applied to thehorizontal rigid slab. For each rod, A = 2000 mm2 α = 11 .7 μm/m0 C, and E = 200 Gpa. Determine therelationship between the force in rod C and the changein temperature ∆. Neglect mass of the slab.
What is the Vertical component (y-component) reaction force at support C? A. 600N, ( + ) upward B. 200N, (+) upward C. 600N,(-) downward D. 200N,( - ) downward SHOW SOLUTIONS
What is the area of the tube? What is the total length of the median line? What will be the result shear flow of the object? The shearing stress value will be The angle of twist will be
Explain about the Vane-Shear Test.
Step 2 1st condition Bending moment at hinge D =0 Rc*2 = (3*2)*(2/2) Rc = 3 KN Rc = 3 KN (upward) could you explain where these numbers coming? Why that divided by two? and is formula like this: 3kN/m*2m*2m/2m? 2nd condition Bending moment at hinge F =0 RB*2= (3*4)*(3+4/2)-3*7 RB = 19.5 KN RB = 19.5 KN ( upward) Same this formula If you can explain this like drawing this on paper and write where all meters and number come, that would be help me. If you could also tell the direction, where you would calculation them
11. A rectangular channel with width = 10 meters and depth = 3 meters has a flow slope of 0.001 and roughness n = 0.025. The flow rate is 80 m3/s. Determine the shear stress on the channel in Pascals.