The state of stress at a point in a structure is shown on the following element. Determine the principle stresses (0₁, 02, and 03), the absolute maximum shear stress (Abs max), and the absolute maximum normal stress (Abs max) at this point. 90 psi y 120 psi 30 psi 70 psi Ans. TAbs Max 97.7 lb in ²

The state of stress at a point in a structure is shown on the following element. Determine the principle stresses (0₁, 02, and 03), the absolute maximum shear stress (Abs max), and the absolute maximum normal stress (Abs max) at this point. 90 psi y 120 psi 30 psi 70 psi Ans. TAbs Max 97.7 lb in ²

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.1P: An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec...

See similar textbooks

Similar questions

An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the xy axes, that is, determine crv, tr(_, and t. Show the results on a sketch of an clement oriented at B = 10
A state of stress at a point A is given by σx = 25 MPa, σy = 122 MPa, and τxy = 60 MPa. Determine the equivalent state of stress on an element at the point which represents the principal stresses.
q1 b In 2D XY-plane-stress analysis, how many stress components you need to calculate.Please write/show their names in XY plane on a plane element.
The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5) where the magnitudes of the stresses are |σx|=11 ksi, |σy|=31 ksi, and |τxy|=17 ksi. Determine the state of stress on an element rotated 50∘ counterclockwise from the element shown. Answers should be as σx′=, σy′=, τx′y′= in ksi
At a point in a stressed body, the cartesian components of stress are sigma xx = 60 MPa, sigma yy= -40 MPa, sigma zz = 20 MPa, tau xy = -40 MPa, tau yz = 20 MPa, and tau zx= 30 MPa. Determine: (a) The normal and shear stresses on a plane whose outer normal has the following direction cosines: cos (n, x) = 0.429 ; cos (n, y) = 0.514; cos (n, z) = 0.743
A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa, σy = 4 MPa , tauxy = 3 MPa a. Draw the Mohr circle. On Mohr's circle, mark the location of the x and y planes, mark the angle of rotation θ from the x plane to the σ₁,σ3,and taumax plane. Prove that the angle of rotation of the Mohr circle is 2 times the angle of rotation of the element. b. Write down the coordinates of the center of Mohr's circle and calculate its radius.
Before loading the plate, mark a line with the inclination shown. After the load is applied, the slope of the line decreases by 5x10^-3 rad. Determine the normal stress ?. Consider E = 2.1x106 kgf/cm^2 and v = 0.30. Express your answer in units of kgf/cm^2.
choose the correct answer Shear stress has units: g. None of the above a. Nt .m b. Nt .m2 f. Viscosity v over area d. Nt/2m e. Viscosity v times area c. kN.t/m2
A 6 meter cable is attached to two points of the same elevation on the ceiling room. The two points are three meters apart. A 100N is tied to the center of cable. Determine the stresses in Pascals of each cable if their cross sectional area is equal to 5 mm^2
The state of stress at a point in a member is shown on the rectangular stress element where the magnitudes of the stresses are |σx|=137 MPa and |τxy|=70 MPa. Determine the state of stress on an element rotated 85∘ clockwise from the element shown.
Mohr's Circle The major and minor principal stresses acting at a point are 80 psi compression and 20 psi tension. (a) Draw the Mohr's circle for this stress combination. (b) What is the maximum shear stress acting at the point, and what value of normal stress acts on the plane? (c) Determine the value of the shear and normal stress acting on a plane that is 30° from the major principal plane. kindly answer the following with a complete solution so that i can understand how to solve it. thank you
At a point of a material, the stresses forming a two-dimensional system are shown inFigure Q1. By using Mohr's circle of stress method: -(i) determine the magnitudes of the principal stresses.(ii) determine the directions of the principal stresses.(iii) Examine the value of the maximum shearing stress.