The load current with an average value of lo is continuous with negligible ripple content The turns ratio of the transformer is 1:2. If the delay angle is oc = n/3. Ira D, 후 Dm lon Fig. Calculate (a) Harmonic Factor (HF) of input current. (b) Transformer Utilization Factor (TUF) (c) Efficiency of the semi converter

The load current with an average value of lo is continuous with negligible ripple content The turns ratio of the transformer is 1:2. If the delay angle is oc = n/3. Ira D, 후 Dm lon Fig. Calculate (a) Harmonic Factor (HF) of input current. (b) Transformer Utilization Factor (TUF) (c) Efficiency of the semi converter

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.17P: The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of...

See similar textbooks

Similar questions

A 20-kVA 8000/277-V distribution transformer has the following resistances and reactance: RP = 32 Ω RS = 0.05Ω X P = 45Ω XS = 0.06Ω RC = 250 kΩ X M = 30 kΩ The excitation branch impedances are given referred to the high-voltage side of the transformer. (a) Find the equivalent circuit of this transformer referred to the high-voltage side. (b) Find the per-unit equivalent circuit of this transformer. (c) Assume that this transformer is supplying rated load at 277 V and 0.8 PF lagging. What is this transformer’s input voltage? What is its voltage regulation? (d) What is the transformer’s efficiency under the conditions of part (c)?
A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:10), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (20:1) and a load with magnitude Z=10 Ohm and angle =30 degree the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the per-unit current in the line Select one: a. 1.43 A b. 0.569 A c. None of the above d. 2.01
A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:10), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (20:1) and a load with magnitude Z=10 Ohm and angle =30 degree the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the per-unit impedance of the load. Select one: a. 1736 (45 degree) Ohm b. 36 (90 degree) Ohm c. 1.736 (30 degree) Ohm d. None of the above
A 240-kVA, 480/4800-V, step-up transformer has the following constants: Rs = 2.5 Ω, Xs = j5.75 Ω, Rp = 25 mΩ, Xp = j57.5 mΩ. The core-loss resistance and the magnetising reactance on the high-voltage side are 18 kΩ and j12 kΩ, respectively. The transformer is operating at 50% of its rated load. If the load is purely resistive, determine the percent power efficiency of the transformer
Given a 115kV/13.2kV distribution transformer rated at 30MVA with an 8% nameplate impedance what is the full Load current in amps
A 72VA, 60Hz single-phase transformer has the equivalent circuit shown. (a) What is the no-load current if excited on the 120V side?(b) Estimate the losses in the transformer at full load with power factor 1.0.(c) Estimate the input voltage required for full load if the output voltage is 36V-rms and the output currentlags the voltage by 25 degrees.(d) What is the voltage regulation?Ans:(b) 4.68W (c)V_p = 123 angle(0.65) V rms (d) 2.5% Show me how each answer was found
A 150-kVA single-phase transformer has a core loss of 1.5 kW and a full-load Cu loss of 2 kW. Calculate the efficiency of the transformer (a) at full-load, 0.8 p.f. lagging (b) at one-half full-load unity p.f. Determine also the secondary current at which the efficiency is maximum if the secondary voltage is maintained at its rated value of 240 V
Using the parameters from the Typical Transformer Values Sheet for a 12.4kV/600V, 100 kVA transformer operating at its rated voltage on the secondary side with its rated load with a PF of 0.8 lagging. Determine for each of the transformer models – deluxe, medium, and economy: Draw the circuit diagram. Find: The magnitude of voltage at the input to the primary side, The power factor on the primary side, The reactive power absorbed by the transformer, The efficiency of the transformer, The voltage regulation of the transformer.
A Transformer with 10:1 ratio and rated at 50-kVA, 2400/240-V, 50-Hz is used to step down the voltage of a distribution system. The low-tension voltage is to be kept constant, if the transformer has: R = 2.2 0, R2 = 0.014 Q, X, = 4.1 0, X2 = 0.03 0, then, a. What load impedance connected to low-tension side will be loading the transformer fully. b. Calculate the equivalent resistance as referred to primary. c. Calculate the equivalent reactance as referred to primary. d. Calculate the equivalent impedance as referred to primary. e. Calculate the total Cu loss.
A 2.4-kVA, 2400/240-V, 50-Hz, step-down transformer has the followingparameters: R, = 1.5 a, X, = 2.5 R, R, = 0.02 a, X, = 0.03 Q, R,, = 6 kR,and X,, = 8 kR. It is operating at 80% of its load at unity power factor.Using the exact equivalent circuit embodying the ideal transformer, determine the efficiency of the transformer. Also sketch its phasor diagram.
A transformer has a ratio of 4:1. The high voltage side is connected to a 240 Vrms source. The low voltage side (secondary) is connected to an impedance ZL = 20 + j10 Ω.a. What is the value of the load impedance when referred to the primary?b. (in A rms) What is the current out of the source?
a) You have been employed as an electrical engineer by a power transmission company to design a short transmission line to supply power to a light-industrial load consumer with power system specification as follows, a 3-ph, 60Hz overhead short transmission line with a line-to-line voltage of 23KV at the load end, line impedance of 2.48 ±j6.57Ω/phase, the industry has a cumulative consumption of 9MW with a power factor of 0.85 of lagging as a result of several induction motor on its production lines.As part of the regulations for connections to the grid, you are to provide justifications and values to the Energy Commission of Ghana.(i) What would be value of the voltage between the live conductor and the neutral, between live and live voltages at the industrial premises of the factory?(ii) What load angle would expect the factory to be operating at?