Situation 9 - A tubular post is hit by a car at point B as shown. The post is fixed to the ground at point A. Given the following data: Cross section of the post = 300 mm x 300 mm Thickness of the Post = 12 mm Force from the Car, P = 165 kN Youngs's Modulus of Elasticity, E = 200 CPa H = 2.5 m; h= 1.5 m h is the den 27. What is the resulting maximum bending stress (MPa? A. 332 B. 621 C. 356 D. 194 H

Situation 9 - A tubular post is hit by a car at point B as shown. The post is fixed to the ground at point A. Given the following data: Cross section of the post = 300 mm x 300 mm Thickness of the Post = 12 mm Force from the Car, P = 165 kN Youngs's Modulus of Elasticity, E = 200 CPa H = 2.5 m; h= 1.5 m h is the den 27. What is the resulting maximum bending stress (MPa? A. 332 B. 621 C. 356 D. 194 H

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The floor system of a residential building (LL=1.9KPa) consists of 125mm thick reinforced concrete slab (unit weight = 23.6 KN/m^3) resting on three 8 m spanned RC floor beams spaced at 2.5 meters on centers. Size of RC beam is 200mm x 450mm. NSCP 2015 Load factors: 1.2DL & 1.6LL. Assume simple supports. Calculate the ultimate/factored live load in KN/m. Express your answer in 1 decimal place.
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa
Determine the intensity of the external dead load D? the reinforced concrete beam shown in the figure canresist. Consider the known self-weight of the beam as part of the dead load. Density of the reinforced con-cretd = 120 lbf/in3. Assume that the service dead load D? (not self-weight) and live load L are equal (D? =L); f ’c = 5,000 lbf/in2, fy = 50,000 lbf/in2. Apply Load Combo 2 only (1.2D + 1.6L). Exploit the instructorspreadsheet calculator posted in D2L to speed up the numerical calculations.
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 19 mm and an elastic modulus of E = 69 GPa. The steel rod has a diameter of 22 mm and an elastic modulus of E = 190 GPa. Assume a = 4.8 m, b = 1.7 m, and c = 1.3 m. What is the magnitude of load P that is necessary to displace point A 9 mm to the left?
A tapered rod with length c = 7m and cross - sectional dimensions a = 270n mm and b = 119 mm is carrying an axial load P = 75kN . If the modulus of elasticity of the rod is E = 164GPa , determine the elongation of the rod in mm . Final ans. in 3 dec place
The cantilever beam above is made up of concrete with E = 70 MPa, refer to the table below for the properties and loads for the beam: Given: b(mm) = 250 h(mm) = 400 w(kN/m) = 15 Mb(kN-m) = 45 Using area moment method, determine the following: 1. Vertical reaction at A, RA. 2. Moment reaction at A, MA. 3. Flexural rigidity of the beam in N-mm^2 4. Rotation at B, in degrees. 5. Rotation at C. in degrees. 6. Deflection at B in mm. 7. Maximum deflection of the beam in mm. 8. If a concentrated load will be placed at B to remove the deflection at C, determine the magnitude of this load in kN.
Determine the x, y, z components of internal loading at a section passing through point B in the pipe assembly. Neglect the weight of the pipe. TakeF1 = {100i - 200j - 300k} N and F2 = {100i + 500j}N.
The floor system of a residential building consists of 125mm thick reinforced concrete slab (unit weight =23.6KN/m^3) resting on the three 8m spanned RC floor beams spaced at 3.3 meters on center. Size of RC beam is 200mm x 450mm. NSCP load factors: 1.2DL & 1.6LL. Assume simple supports. Calculate the unfactored slab load in KN/m? express your answer in 1 decimal place.
A tubular steel strut 2 m long, both ends hinged, must have a buckling load of120 kN, based on the Euler formula. The outside diameter is 60 mm. Calculatethe thickness required. What will be the factor of safety according to Rankine's formula if yield strength = 350 MPa and Rankine's constant is 1/7500 for hinged ends? (E = 200 GPa.)
The rigid bar AD is supported by two steel wires of 1.5 mm diameter (E = 200 GPa) and a pinand bracket at D. Knowing that the wires were initially taut, determine the stress in each wirewhen a 1200 N load P is applied at D. What is the corresponding deflection of point D?
What is the internal force in member AB? A. 750 N , T B. 450 N , T C. 750 N , C D. 450 N , CSHOW SOLUTIONS
The cross section of a continuous one way slab in a building is shown in the figure. The slabs are supported by means of beams that span 3.6 m between simple supports. The dead load on the slab is 3 kPa (besides its own weight) and a live load of 7 kPa. =21 MPa, =276 MPa. Use 20 mm clear cover. Unit weight of concrete = 24 kN/m3.a) Determine the thickness of slabb) Determine the spacing of 16 mm bars at section CDc) Determine the spacing of 16 mm bars at section E.