Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the total deformation on the steel. Steel Brass Copper Ecu = 120 GPa 17(10-)/°C Est = 200 GPa Ebr =100 GPa %3D 12(10-6)/°C apr = 21(10-6)/°C acu %3D ast Acu = 515 mm² Ast = 200 mm² Abr = 450 mm? %3D 300 mm- --200 mm 100 mm O -0.0058mm O 0.0165mm

Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the total deformation on the steel. Steel Brass Copper Ecu = 120 GPa 17(10-)/°C Est = 200 GPa Ebr =100 GPa %3D 12(10-6)/°C apr = 21(10-6)/°C acu %3D ast Acu = 515 mm² Ast = 200 mm² Abr = 450 mm? %3D 300 mm- --200 mm 100 mm O -0.0058mm O 0.0165mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
A brass (? =5.6 ? 10^6 ???) and aluminum (? = 3.7 ? 10^6 ???) cylinders are bonded together at B, and are attached to fixed supports A and C. Determine (a) The torsion in AB, (b) The torsion in BC, (c) The maximum shearing stress in AB (d) The maximum shearing stress in BC.
Steel bar of cross-section 550mm2 is acted upon by the forces shown in figure. For steel, E = 200GPa. Compute the stress in BC Compute deformation of AB Compute the total elongation of the assembly.
A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are ϵx = 0.40 x10-3 and ϵy = 0.30 x10-3, determine σx and σy. Use E = 110 GPa and v = 0.35.
A steel rod of 30 mm diameter is inserted in a copper tube of external diameter 45 mm and an internal diameter of 37 mm carries a load of W =1750kN. The length of this compound bar is 180 mm. If, ES= 2 × 105 N/mm2and ECu= 1 × 105 N/mm2, calculate the stresses developed in copper and steel.
At room temperature (10 C)° a 0.25-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 130°C, determine the normal stress in the each rod * 0.25 250 mm 200 mm B Aluminum A 2000 mm² E = 75 GPa a = 23 × 10 6°C Stainless steel A = 800 mm² E = 190 GPa a = 17.3 X 10-6PC
Determine the following reactions using method of joints. Stress= F/A Ac- 40 mm^2 At= 50 mm^2 E= 200 Gpa Deformation = PL/AE
1. Titanium alloy with an elastic modulus of 107 GPa (15.5 x 106 psi) and an initial diameter of 3.8 mm (0.15 in. ), only elastic deformation occurs. If the maximum permissible elongation is 0.42 mm, find the specimen's maximum length before deformation (0.0165 in.) 2.) With a load of 89,000 N (20,000 lbf), a steel bar 100 mm (4.0 in.) long with a square cross section 20 mm (0.8 in.) on one edge is pulled in tension and undergoes an elongation of 0.10 mm (4.0 103 in.). Calculate the steel's elastic modulus, assuming the deformation is fully elastic. Please indicate the given sir. Thanks alot…
The two wooden boards shown in the figure are connected by a 0.5 in. diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D  2 in. and d 5/8 in. The nut is tightened to cause a tensile stress of 9,000 psi in the bolt. Determine the bearing stress MPa between the washer and the wood
An aluminum tube is fastened between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. For Bronze: Allowable stress = 120 MPa, EB = 83,000 MPa For Aluminum: Allowable stress = 120 Mpa, EA = 70,000 MPa For Steel: Allowable stress = 120 MPa, Es = 200,000 MPa Assume that the assembly is suitably braced to prevent buckling. Maximum overall deformation should not exceed 2mm. a) Give the value of the force acting on the bronze so as not to exceed allowable stresses and deformation. b) Give the value of the force acting on the aluminum so as not to exceed its allowable stresses and deformation. c) Give the value of the force acting on the steel so as not to exceed its allowable stresses and deformation.
Value of P1=9 kNP2=105 kNP3=89 kNd=159 mm Strength of Materials