56.0 mL of two different liquids are poured through a funnel with a narrow exit tube, and the time forall of the liquid to flow through is recorded. Here are some results:time to flow through funneltrialLiquid XLiquid Y1.60 s3.62 s1.52 s3.44 s1.44 s3.56 sNote: the two liquids have the same density.Which statement below is true about these liquids based only on the data in the table?O The intermolecular forces in liquid X are stronger than those in liquid Y.The boiling point of liquid X is higher than the boiling point of liquid Y.The viscosity of liquid X is greater than the viscosity of liquid Y.The surface tension of liquid X is greater than the surface tension of liquid Y.The viscosity of liquid X is less than the viscosity of liquid Y.3.

1.The first statement is false. The correct statement is intermolecular forces in liquid Y is more…

56.0 mL of two different liquids are poured through a funnel with a narrow exit tube, and the time for all of the liquid to flow through is recorded. Here are some results: time to flow through funnel trial Liquid X Liquid Y 1 1.60 s 3.62 s 1.52 s 3.44 s 3 1.44 s 3.56 s Note: the two liquids have the same density. Which statement below is true about these liquids based only on the data in the table? The intermolecular forces in liquid X are stronger than those in liquid Y. The boiling point of liquid X is higher than the boiling point of liquid Y. The viscosity of liquid X is greater than the viscosity of liquid Y. The surface tension of liquidX is greater than the surface tension of liquid Y. The viscosity of liquid X is less than the viscosity of liquid Y. O O O O O

56.0 mL of two different liquids are poured through a funnel with a narrow exit tube, and the time for all of the liquid to flow through is recorded. Here are some results: time to flow through funnel trial Liquid X Liquid Y 1 1.60 s 3.62 s 1.52 s 3.44 s 3 1.44 s 3.56 s Note: the two liquids have the same density. Which statement below is true about these liquids based only on the data in the table? The intermolecular forces in liquid X are stronger than those in liquid Y. The boiling point of liquid X is higher than the boiling point of liquid Y. The viscosity of liquid X is greater than the viscosity of liquid Y. The surface tension of liquidX is greater than the surface tension of liquid Y. The viscosity of liquid X is less than the viscosity of liquid Y. O O O O O

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

Measurements at a certain point of a pipe have been done where the following parameters were recorded: Fluid of density = 887 kg/m3, Fluid velocity = 4 m/s, Pressure= 11.3 KN/m2 If the total energy per unit weight at this point = 32 m, then the potential energy is:
A liquid with a specific gravity of 4.7 and a viscosity of 1.3 cp flows through a smooth pipe of unknown diameter, resulting in a pressure drop of 0.183 lbf/in² for 1.73 mi. What is the pipe diameter in inches if the mass flowrate is 5,900 lb/hr?A. 3.64 inB. 0.44 inC. 5.74 inD. 0.005 in
A fluid flows through a pipe and exits into a container that sits on some scales. At the beginning of the pipe the velocity is 6m/s After 156s, the scale shows 7733N. The pipe outlet diameter is 0.1m, and is four times greater than the inlet. Determine the density of a fluid
An airplane builder wants to build a scaled-down model of a real airplane in a 12:1 ratio in order to be able to perform tests in a wind tunnel. The real plane flies at 126 km/h, while the air speed in the tunnel where the model is located is given by V. The performances of the two will be equivalent for a value of V, in m/s, equal to Data: air viscosity η = 1.8 × 10-5 kg/(m.s) air density ρ = 1.3 kg/m3
The pressure drop in a venturi meter (Fig. P3.128) varies onlywith the fluid density, pipe approach velocity, and diameterratio of the meter. A model venturi meter tested in water at20 ° C shows a 5-kPa drop when the approach velocity is 4 m/s.A geometrically similar prototype meter is used to measuregasoline at 20 °C and a flow rate of 9 m 3 /min. If the prototypepressure gage is most accurate at 15 kPa, what should theupstream pipe diameter be?
Find the pressure drop between locations a and b for flow in a pipe using the following data: Working fluid: Water Pipe: Stainless steel, Schedule No. 120 Nominal pipe size (cm): 10 Flow rate (m3 /min): 2.271 Temperature (C): 38 Length (m): 45.72 Solve for the following 3 cases: a) Za = Zb =33.5 m, b) Za = Zb + 15 m, and c) Za = Zb + 46 m.
At any time, approximately 20 volcanoes are actively erupting on the Earth, and 50–70 volcanoes erupt each year. Over the past 100 years, an average of 850 people have died each year from volcano eruptions. As scientists and engineers study the mechanics of lava flow, accurately predicting the flow rate (velocity) of the lava is critical to saving lives after an eruption. Jeffrey’s equation captures the relationship between flow rate and viscosity as: where ρ is the density of the lava, g is gravity, t is the flow thickness, α is the slope, and m is the lava viscosity. Typical values are given as follows for the flow rate: m= 4x103 kg/(m.s) ±1% ρ= 2.5 g/cm3 ±1% t= 28 cm ±0.5 cm α= 10° ±1 ° g= 9.81 m/s²
PROPAGATION OF ERROR You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. if the diameter measurement is off by 0.1m and the anemometer reading is also fluctuating by 0.05m/s. In the design specifications given, if the actual measurement of power via the substation amounts to exactly 530kW and given that the windspeed is off by 0.05m/s, what could have been the error in the measurement of diameter? Your answer must be in 3 decimal places and in correct signs and measurement. Show complete solution in paper.
An incompressible fluid flows in a linear porous medium with the following properties: Lenth = 3000 ft k = 100 md p1 = 2000 psig p2 = 1980 psig height = 25 ft porosity = 20% width = 300 ft viscosity = 2 cP Assume the dimension is slanted, i.e., a dip angle of 5 degrees (downward from p1 location to p2 location), what is the apparent fluid velocity under this new boundary condition?
Problem statement : A simple flow-measurement device for streams and channels is a notch, of angle α, cut into the side of a dam, as shown in Fig. P5.69. The volume flow Q depends only on α, the acceleration of gravity g, and the height δ of the upstream water surface above the notch vertex. Tests of a model notch, of angle α = 55°, yield the following flow rate data: δ, cm: 10 20 30 40 Q, m3/h: 8 47 126 263 Part (A) - Find a dimensionless correlation for the data. (b) Use the model data to predict the flow rate of a prototype notch, also of angle α = 55°, when the upstream height δ is 3.2 m.
Under a laminar flow, the liquid flows through small holes. It has a triangular cross-section, width b and length L, where the volumetric flow rate Q of the flow is a function of viscosity. ,pressure reduction per unit length p/L and width b 1) Use the PI theory to write the relationship as a dimensionless variable. 2) if the width b is doubled by viscosity And the pressure drop per unit length p/L is the same. I want to know how the flow rate Q will change.
Wind blows and pasts a banner causes it to flutter. The fluttering frequency f is a function of the wind speed V, the air density ρ, the acceleration of gravity g, the length of the banner L and the “area density” of the flag material ρA (with dimensions of ML-2 ). In order to estimate the flutter frequency of a large banner with L = 40 ft in a V = 30 ft/s wind, a small banner with L = 4 ft is to be tested in a wind tunnel. (a) What is the area density of the small banner when the large banner has area density of 0.006 slugs/ft2? (b) What should the wind tunnel velocity be to test the small model? (c) It has been shown that the small banner flutters at 6 s-1 when the same area density and wind tunnel velocity are used in parts (a) and (b). In this case, what is the fluttering frequency of the large banner?