Structural member AB is supported by cable BC and at A by a square rod which fits loosely through the square hole in the collar fixed to the member. Two forces are applied to AB as shown. 1.5 m 3 m Determine: 400 N a. Support reactions at A b. Cable tension Draw all FBD's needed to solve, show all work, and put units on your answers. 200 N x 1m

Structural member AB is supported by cable BC and at A by a square rod which fits loosely through the square hole in the collar fixed to the member. Two forces are applied to AB as shown. 1.5 m 3 m Determine: 400 N a. Support reactions at A b. Cable tension Draw all FBD's needed to solve, show all work, and put units on your answers. 200 N x 1m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Similar questions

Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
P = 80 kN σt = 150 MPa t = 8.0782 mm Can you help me solve for d2?
A load of P = 4900 N is acting on member AC. The length of AC is d = 300 mm. The cross-sectional area of AB is 375 mm2 while the cross-sectional area of C is 575 mm2 . Determine the magnitude (in N) of the force acting on rod AB if the compressive stress in the smooth support C is equal to the tensile stress in the rod AB. Round off the final answer to two decimal places.
A horizontal board weighing Wb = 600 N is hinged to a vertical wall. A personweighing Wp = 400 N stands at the end of the board 5 m from the wall. A rope is attached to theboard at a point 3 m from the wall and makes an angle of θ = 40° with theboard. Determine the tension (T) in the rope
A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0,respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the leftend where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) andthe weight (W) of the bar
In a hydraulic press the diameter of the plunger is 50 mm . Find the diameter of the hydraulic press side when the force at hydraulic press side is 22050 N to lift the weight at the plunger of 450N. a. 350 mm b. 250 mm c. 500 mm d. 100 mm
A triangular block shown is subjected to the loads S = 1000 lb and T = 2000 lbs. If AB = 8 in and BC = 6 in, resolve each load into components normal and tangential to AC.
The triangular block below is subjected to the Loads P=1200 lb and 400 lb. If AB=8 in, and BC is 6in., resolve each load into components normal and tangential to AC.
A cylinder speamen 380 mm bital length. If the load force of 6660N with Madual of Elashicly 110gpa and elongadium of 0.5mm then determine the diameter of test cylinder ?
The truss above has concentrated loads as shown. The wind loads of 50 KN are perpendicular to the member AF. Solve for the forces acting on the members BE, DE, DG, FG by the method of joints. Show all solutions please don't skip. Please show to did u get FBC, FBE, FBD Thanks!FBDsin30-FBEsin60-FBC = 243.301KN then FBC = -625.77KN. how?did you divide 243.301KN to sin30 + sin 60?? please write the solution down and i'll thumbs up to all ur answers thanks!
P1=215 N P2=325 N P3=150 N L1=3m L2=4m 1. Draw a "free body diagram". The diagram should be for members BE, BF, CF, and DF to help solve. 2. What is the force on members CF, BF, BE? Is each of these members having tension or compression?
1. A museum of modern art is displaying an irregular 426-N sculpture by hanging it from two thin vertical wires, A and B, that are 1.25 m apart. The center of gravity of this piece of art is 48.0 cm from its extreme right tip. a). Find the tension in each wire. Show the step by step and complete solution. Draw also the complete FBD (as seen in the figure).