Suppose that the pitch of the threads of the turnbuckle is p = 0.05 in, their meanradius is r= 0.25 in, and the coefficient of static friction between the threads andthe mating grooves in 0.25.What is the pitch angle (in degrees) of the thread?2.2817.660.911.8213.7If T = 250 lb, what couple (in pound-in) must be exerted on the turnbuckle tostart loosening it? *15.510.320.727.113.5If T = 250 lb, what couple (in pound-in) must be exerted on the turnbuckle tostart tightening it?O 13.715.835.517.827.4

We will answer the first question since the exact one was not specified. Please submit a new…

Suppose that the pitch of the threads of the turnbuckle is p= 0.05 in, their mean radius is r= 0.25 in, and the coefficient of static friction between the threads and the mating grooves is 0.25. What is the pitch angle (in degrees) of the thread? O 228 O 17.66 O 0.91 O 1.82 13.7

Suppose that the pitch of the threads of the turnbuckle is p= 0.05 in, their mean radius is r= 0.25 in, and the coefficient of static friction between the threads and the mating grooves is 0.25. What is the pitch angle (in degrees) of the thread? O 228 O 17.66 O 0.91 O 1.82 13.7

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A box rests on a horizontal plane. The plane is slowly tilted so that the angle between the surface and the horizontal increases to 20 degrees, at which point the box begins to slip. what is the coefficient of static friction between the box and the surface to 2 s.f.?
A 30 KN of force at one end just supports a weight of 30,000 KN load at the other end. If the rope is run three times around a circular post, what is the coefficient of friction between the rope and the post?
A ladder of length 5 m is resting against a smooth wall, its point of contact being just below a first floor window. The bottom of the ladder rests on the ground and the coefficient of friction between the ladder and the ground is 0.3. A person of mass 75 kg climbs the ladder, which has a mass of 4 kg. The bottom of the ladder is at the point of slipping, outward from the wall, just as the person reaches the mid-point of the ladder’s length. Draw a free body diagram of the ladder and calculate the maximum frictional force opposing the slipping motion. In addition, determine the angle of inclination (θ) of the ladder, when the person is at the mid-point and the ladder is on the verge of slipping.
A 30 KN of force at one end just supports a weight of 30,000 KN load at the other end. If the rope is run three times around a circular post, what is the coefficient of friction between the rope and the post? How to get the final answer 0.366?
An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the corresponding angles of lap are 160° and 210°. The smaller pulley runs at 200 r.p.m. The coefficient of friction between the belt and pulley is 0.25. It is found that the belt is on the point of slipping when 3 kW is transmitted. To increase the power transmitted two alternatives are suggested, namely (i) increasing the initial tension by 10%, and (ii) increasing the coefficient of friction by 10% by the application of a suitable dressing to the belt. Which of these two methods would be more effective? Find the percentage increase in power possible in each case.
Problem 4. A.) If the uniform concrete block has a mass of 500 kg, determine the smallest horizontal force P needed to movethe wedge to the left. The coefficient of static friction between the wedge and the concrete and the wedge and the floor is 0.3. The coefficient of static friction between the concrete and floor is 0.5.ANSWER: P=1797.52; N=1.80kNB.)Refer to problem number 4. Calculate the followinga.) the angle of friction between the wedge and the concrete and the wedge and the floor.Answer: ?????? ??? ????????= ?????? ??? ?????= 16.7ob.) the coefficient of static friction between the concrete and floor.Answer: ????????? ??? ?????= 263.56o
The pitch of 48 mm mean diameter threaded screw of a screw jack is 12.0 mm. The coefficient of friction between the screw and the nut is 0.12. (a) Determine the torque required on the screw to raise a load of 27 kN, assuming the load to rotate with the screw. (b) Determine the ratio of the torque required to raise the load to the torque required to lower the load and also (c) the efficiency of the machine.
The coefficient of static friction under the block a and b are the same. If the block is in the verge of sliding, find the tension at each chord. Assume that the pulley is frictionless.Recall [from Physics]:?? = ???Where:?? - is the frictional force?? - is the normal force? -coefficient of static frictiona. Determine the tensile force (lb) on the cable 1.b. Determine the tensile force (lb) on the cable 2. Plsss show complete handwritten solution. Thanksss!!
A pulley with a diameter of 4 in. can rotate about a fixed shaft with a diameter of 2 in. The coefficient of static friction between the pulley and shaft is 0.20. Determine; a. the smallest vertical force P required to start raising a 500-lb load. b. thesmallest vertical force P required to hold the load. c. the smallest horizontal force P required to start raising the same load.
High-strength bolts are used in the construction of many steel structures. For a 1-in.-nominal-diameter bolt, the required minimum bolt tension is 51 kips. Assuming the coefficient of friction to be 0.30, determine the required couple that should be applied to the bolt and nut. The mean diameter of the thread is 0.94 in., and the lead is 0.125 in. Neglect friction between the nut and washer, and assume the bolt to be square-threaded.
A block is resting on a wooden plank. There is a hinge on one end of the plank which allows the other end to be lifted to create an angle, θ, with respect to the horizontal as shown in the figure. The coefficient of static friction between the block and the plank is μs. If a student measures that the block begins to move at an angle of θ = 20.5°, what is the numerical value of the coefficient of static friction, μs?
2 A ladder 5 m long and weighing 260 N is placed against a vertical wall at an inclination of 30 ^ 0 with wall. A wan weighing 780 N climbs the ladder. When he is at a distance of 1.64 m along the ladder from lower all contact surfaces? end, the ladder slips. What is the coefficient of friction assuming it to be same for