Table 5: Mass and Volume Measurements for Unknown Metal Initial volume of water in graduated cylinder (mL) Volume of water and Unknown Metal (mL) Mass of graduated cylinder with water (g) Mass of graduated cylinder with water and Unknown (g) Total Mass of Unknown Metal Volume of water displaced by metal Density of Unknown Metal (g/mL) 20mL Trial 1 24 mL 95mL 125.00 g 30g 2mL Trial 2 20mL 26 mL 95mL 140.00 g 45g 6mL Trial 3 20mL 28mL 95mL 155.00 g 60g 8mL Average Density Calculation: Identity of Unknown Metal Use density values provide in https://periodictable.com/Properties/A/Density.an.html

Table 5: Mass and Volume Measurements for Unknown Metal Initial volume of water in graduated cylinder (mL) Volume of water and Unknown Metal (mL) Mass of graduated cylinder with water (g) Mass of graduated cylinder with water and Unknown (g) Total Mass of Unknown Metal Volume of water displaced by metal Density of Unknown Metal (g/mL) 20mL Trial 1 24 mL 95mL 125.00 g 30g 2mL Trial 2 20mL 26 mL 95mL 140.00 g 45g 6mL Trial 3 20mL 28mL 95mL 155.00 g 60g 8mL Average Density Calculation: Identity of Unknown Metal Use density values provide in https://periodictable.com/Properties/A/Density.an.html

Chemistry: The Molecular Science

5th Edition

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:John W. Moore, Conrad L. Stanitski

Chapter1: The Nature Of Chemistry

Section: Chapter Questions

Problem 85QRT

See similar textbooks

Similar questions

Hexane (C6H14, density = 0.766 g/cm3), perfluoro-hexane (C6F14, density = 1.669 g/cm3), and water are immiscible liquids; that is, they do not dissolve in one another. You place 10 mL of each in a graduated cylinder, along with pieces of high-density polyethylene (HDPE, density = 0.97 g/cm3), polyvinyl chloride(PVC, density = 1.36 g/cm3), and Teflon (density = 2.3 g/cm3). None of these common plastics dissolves in these liquids. Describe what you expect to see.
Vanadium metal is added to steel to impart strength. The density of vanadium is 5.96 g/cm3. Express this in SI units (kg/m3).
How many square meters will 4.0 L (about 1 gal) of paint cover if it is applied to a uniform thickness of 8.00 102 mm (volume = thickness area)?
The active ingredient of aspirin tablets is acetylsalicylic acid, which, has a density of 1.4 g/cm3. In a lab class, a student used paper chromatography to isolate another common ingredient of headache remedies. The isolated sample had a mass of 0.384 g and a volume of 0.32 cm3. Given the data in the following table, what was the other ingredient in the headache remedy? Density Values for Potential Headache Remedies Compound Density (g/cm3) White table sugar 0.70 Caffeine 1.2 Acetylsalicylic acid 1.4 Sodium chloride 2.2
Metal A dissolves in nitric acid solution. You can recover the original metal if you place Metal B in the solution. Metal A becomes heavier after prolonged exposure to air. The procedure is faster if the metal is heated. From the evidence given, can you tell if Metal A definitely is or could be an element or a compound? If you cannot, what other information do you need to make that classification?
1.65 An industrial engineer is designing a process to manufacture bullets. The mass of each bullet must be within 0.2 5% of 150 grains. What range of bullet masses, in mg, will meet this tolerance? 1 grain = 64.79891 mg.
Visit this PhET density simulation (http://openstaxcollege.org/l/16phetmasvolden) and select Custom Blocks and then My Block. Enter mass and volume values for the block such that the mass in kg is less than the volume in L. What does the block do? Why? Is this always the case when mass volume How would (a) and (b) be different if the liquid in the tank were ethanol instead of water How would (a) and (b) be different if the liquid in the tank were mercury instead of water
The density of an irregularly shaped object was determined as follows. The mass of the object was found to be 28.90 g 0.03 g. A graduated cylinder was partially filled with water. The reading of the level of the water was 6.4 cm3 0.1 cm3. The object was dropped in the cylinder, and the level of the water rose to 9.8 cm3 0.1 cm3. What is the density of the object with appropriate error limits? (See Appendix 1.5.)
You set out to determine the density of lead in the laboratory. Using a top loading balance to determine the mass and the water displacement method (Study Question 41) to determine the volume of a variety of pieces of lead, you calculate the following densities: 11.6 g/cm3, 11.8 g/cm3, 11.5 g/cm3, and 12.0 g/cm3. You consult a reference book and find that the accepted value for the density of lead is 11.3 g/cm3. Calculate your average value, percent error, and standard deviation of your results.