Taps are available in sets of 3, Plug, Second & Taper. Which should be used First? M20 17.5mm Plug Oa. Тарer Ob. Second Oc. None of the above Od. 12:13 pm /

Q: Daw the Free buly Dingram

A: Free body diagram of given figure

Q: List five thing that are typically removed when removing a transaxle

A: The things that are typically removed when removing a transaxle :-

Q: Explain the job of Rudder

A: The rudder is a primary flight control surface that controls rotation about the vertical axis of an…

Q: what is the impact of mechanical vibration on following a. Bearing House of Lathe machine b.…

A: Answer         c. Fatigue life of materials

Q: A tool used for making internal threads in G. I. pipes   Pipe Reamer Pipe Vise Pipe Extractor…

A: Galvanized pipe is steel pipe with a zinc coating that prevents the steel from corroding. It's…

Q: Q3: (a) describe the location and function of the following: i. Gudgeon pin ii. Rod shank ii.Large…

A:

Q: Which of the following material is used to connect D Select one: Square box Saddle clip Coupling…

A: Option c is correct.

Q: The threading of G.I. pipes for installation of water system may be accomplished using two competing…

A:

Q: Draw the shear and moment diagrams for the beam

A: Draw the free body diagram of the beam and calculate the reactions: Apply static equilibrium…

Q: ermissible working tokon as 25

A:

Q: please explain for c) what is Sum of M at hinge

A:

Q: Q-2 What is the value of the Ely 400 N| 400 N/m 3m 1m A 1m

A:

Q: peed shaft

A: equation of Motion of Generators    4 ENERATOR J_{2}   J ² θ 2 ^ +k t 2 (θ_{2} - θ_{1}) = 0 using…

Q: Describe two types of benders for soft tubing.

A: A metal pipe bender is an important machine tool that provide pipe bends for a vast number of…

Q: s (m) ,s = - -2t + 2 - 1 (s) 2.

A: Given data:-    s= -2t+2 (m)  Draw velocity and acceleration diagram with respect to time

Q: In a lathe machine maintenance work, wiper pads are not necessarily to be dipped in oil to hold the…

A:

Q: Given'- u= 35mls V = om/s t-5secs S-2

A:

Q: specification required for the bolt

A: Given; Three bolt system as shown in figure;The bolt material has ,shear yield…

Q: Draw three views of the adjusting bracket. . Orill-2 Holes 3 BOrill

A: The figure below shows the top and front view of the given model.

Q: bent flat bar rotates

A: θ=πsintθ=30o=π6π6=πsintt=9.6 sec…

Q: Lome work A mild steel shaft for a marine engine is- 3500 HP at loorpm Design the coupling? Ts = Coo…

A: Given Data⇒ Power transmitted (P)=3500 HP P=3500×746 P=2.611 MW N=100 rpm ζs=600kgcm2ζs=600×104…

Q: nance pr Tollowed wniie performing gib adjustment on a lathe machine is O On the front face of the…

A:

Q: 1 pitch. What will be the spe. I the output shaft C assumir

A:

Q: Drilling operation to produce conical shape on a drilled hole is known as a. Boring b. Counter…

A:

Q: sing) slope with a c

A:

Q: Draw three views of the adjusting bracket. Drill-2 Holes Drill PROB. 20 Adjusting bracket.

A: Given isometric view of the adjusting bracket  To sketch the three views  Below the three views are…

Q: grees sideways. AB-20, BC-25, CD-30, 8D-50, CF-4Scm. Draw in appropriate scale

A:

Q: (7):- The numbers of production elements are a- 9M b- 6M c- 12M d- 5M

A: The total number of production element are ,

Q: A -A, = 660 mm 2m Cap plate 3m Anc =860 mm

A: Given:AAB=660 mm2ABC=860 mm2E=110 GPaNote: According to Bartleyby's policy we shall answer only…

Q: 1 1. FIMD RXAS AT A D 2. ou Pids oF POLLETS Bx By C- C. C. ALE OF RESUTAT AT B,C &A

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: Definition of bottom dead centre

A:

Q: Industrial Main Describe a plain bearing.

A:

Q: T. A T (N) 750 FRAGILE HANDLE CARE ON' 5 8 t (s ?

A: Given: mass of the package =  106.5 kg

Q: Dons at C, ar 2"

A:

Q: "N" JOBS- “3" MACHINE

A: Where Machine G is - A+B=8+5=13 10+6=16 6+2=8 7+3=10 11+4=15 And Where H - B+C 5+4=9 . .

Q: The straight surface on either side of the screw thread is known as Flank Root Crest Pitch

A:

Q: rd frame and dr.

A:

Q: ety, the maximum ne rod is limited to st be at least 1000

A: Load on the steel rod = 50 tones  = 50×1000 =50000 kg Allowable stress =150kg/mm2 Allowing stress=…

Q: Which manufacturing machine is used for cylindrical symmetric parts? OA Drilling Machine D Laser…

A: CNC turning machine (Lathe) is used to produce the components that are symmetrical about the axis.…

Q: The greater the working load of the bearing, the penetration of grease should be . A. Bigger B.…

A:

Q: Give an outline description of the operation of a GMR Read head.

A: A GMR magnetic media reading head. As the magnetic recording medium passes beneath the GMR sensor,…

Q: machine operated for e ted at A and B. The sha ad on the shaft is indica e following:

A: n=475rpmL10h=25000hrsRelaibility goal =95% To-Find:- 1 Multiple of rating life required2 Catalogue…

Q: figures sho ed to a con Mat the free

A:

Q: A metal disc of 70 mm diameter is to be punched from a sheet of 6 mm thickness. The punch and the…

A: Given data Disc diameter = 70 mm Clearence = 4% = 0.04

Q: able diameter for the bar sho ety factor = 3.

A:

Q: [- hammer is used on domed circular works

A: planishing hammer has a round face, which is used on domed circular work

Q: The wrenches are used for clearing burrs from work surfaces. Select one: True False

A: The wrenches are used for clearing burrs from work surfaces. Select one: True False

Q: 2.... Hydraulic controlled riveting assembly machine. hydraulic control system. Must include the…

A:

Q: Overall combined cycle

A: Given: For two cycles coupled in series,Topping cycle efficiency is;ηtopping=30%=0.3Bottoming cycle…