The stresses at a point on the surface of a generator shaftare o =-50 MPa, o, = 30 MPa and Tryshown in Figure Q3.(Consider only the in-plane stresses. Note: the radius of the= -40 MPa ascircle is given by R = ) + ()).Construct the Mohr's circle showing the centre of the circle aswell as points A and B.(a)(b)Determine the principal stresses.(c)Show the principal stresses on a sketch of a properly orientedelement.(d)Determine the maximum shear stresses.(e)Show the maximum shear stresses on a sketch of a properlyoriented element.MPaB.AMPaMPa

Answered: Image /qna-images/answer/f973183c-47b8-47a9-806d-db42f0351f60.jpg

The stresses at a point on the surface of a generator shaft are o =-50 MPa, o, = shown in Figure Q3. (Consider only the in-plane stresses. Note: the radius of the 30 MPa and Try = -40 MPa as %3D %3D circle is given by R = +(). 2. (a) Construct the Mohr's circle showing the centre of the circle as well as points A and B. (b) Determine the principal stresses.

The stresses at a point on the surface of a generator shaft are o =-50 MPa, o, = shown in Figure Q3. (Consider only the in-plane stresses. Note: the radius of the 30 MPa and Try = -40 MPa as %3D %3D circle is given by R = +(). 2. (a) Construct the Mohr's circle showing the centre of the circle as well as points A and B. (b) Determine the principal stresses.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.16P: A propeller shaft subjected to combined torsion and axial thrust is designed to resist a shear...

See similar textbooks

Similar questions

-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
An element in plane stress is subjected to stresses sx= -5500 psi, sy= -2000 psi, and Tx. = 1900 psi (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
The stresses acting on element A in the web of a train rail are found to be 40 M Pa tension in the horizontal direction and 160 MPa, compression in the vertical direct ion. Also, shear stresses of magnitude 54 MPa act in the directions shown (see the figure b for Problem 7.2-5). Determine the principal stresses and show them on a sketch of a properly oriented element.
Solve the preceding problem if the stresses acting on element A on the web of a train rail (see figure part a of Problem 7.2-5) are found to be 40 MPa in tension in the horizontal direction and 160 MPa in compression in the vertical direction. Also. shear stresses of magnitude 54 MPa act in the direct ions shown in the figure. Determine the stresses acting on an element oriented at a counterclockwise angle of 520 from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
Repeat Problem 8.5-22 but replace the square tube column with a circular tube having a wall thickness r = 5 mm and the same cross-sectional area (3900 mm2) as that of the square tube in figure b in Problem 8.5-22. Also, add force P. = 120 N at B (a) Find the state of plane stress at C. (b) Find maximum normal stresses and show them on a sketch of a properly oriented element. (c) Find maximum shear stresses and show them on a sketch of a properly oriented element.
The stresses acting on a stress element on the arm of a power excavator (see figure) are ax= 52 MPa and txy= 33 MPa (sec figure). What is the allowable range of values for the stress if the maximum shear stress is limited to = 37 MPa?
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
The normal and shear stresses acting on element B are ??x= -46 MPa, sy= -13 MPa, and txy= 21 MPa (see figure for Problem 7.2-10). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.