Can you please complete the following just need help with the question as it's my last to do. The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve . The outerdiameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa,Ebr = 100 GPa.Figure1 of 1P-10 mm- 20 mmP------ ----- --- Part AIf the bolt is subjected to a compressive force of P = 15.3 kN, determine the average normal stress in the steel.Express your answer to three significant figures and include appropriate units.HA?Ost =ValueUnitsSubmitRequest AnswerPart BIf the bolt is subjected to a compressive force of P = 15.3 kN, determine the average normal stress in the bronze.Express your answer to three significant figures and include appropriate units.HẢ?ValueUnitsObrSubmitRequest Answer< Return to AssignmentProvide Feedback

Givend0=20mmdi=10mmEst=200GpaEbt=100GpaP=15.3Kn

Answered: The 10-mm-diameter steel bolt in…

The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve . The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa, Epr = 100 GPa,

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.15P: Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.

See similar textbooks

Related questions

Q: A M12 x 1.25 hex-head bolt with a nut is used to clamp two 25-mm thick steel plates. The nut height…

A: Given:- Elastic modulus 207 GPa Bolt size= M12 x 1.25 Height of nut =10.8 To find:- d) Bolt…

Q: 3. A tie bar is welded to a plate and it is subjected to axial load, P. The length of the fillet…

A: Given data Length of fillet weld (L) = 200 mm size of fillet (s) = 6 mm stress of the fillet weld…

Q: Two short shafts having identical diameters of 35 mm and rotating at 1000 rpm are connected by a…

A: Disclaimer: Since you have posted multiple questions we will solve the first question for you. If…

Q: QUESTION 7 Figure 7 shows an assembly consist of circular shaft AB, solid circular BC and a circular…

A: Torque diagram-

Q: A transmission shaft, supporting two pulleys A and B and mounted between two bearings C, and C, is…

A: 45C8Sut=600 N/mm2Syt=380N/mm2kb=1.5kt=1.0θ=5°G=79300N/mm2dA=200mmdB=300mm To-Find:- Shaft Diameter…

Q: (8) A tension member subjected to a load of 30,000 lb has a cross section % in. by 6 in. and is…

A: given; load(P)=30000lbcross section hole diameter (d1)=6 inpiercing hole diameter(d2)=1 infactor of…

Q: A helical spring of 75 mm radius made of 20 mm turns of 12 mm diameter wire is loaded with 120 N…

A: Springs are elastic members which are distorted under load and regain their original shape when the…

Q: The 10-mm thick component in the figure is designed with a fillet and a hole. The load varies from…

Q: 5. A 2 mm thick C 20 steel sheet is required to be bent at 45° at bend radius 25 mm. Determine the…

A: Given: thickness of sheet (t) = 2 mm bend radius (r) = 25 mm bend angle (θ) =45o = 0.785 rad bend…

Q: A M12 x 1.25 hex-head bolt with a nut is used to clamp two 25-mm thick steel plates. The nut height…

A: Note:- As per our company guidelines we are supposed to answer only the first three sub-parts.…

Q: Al Fe Al Two aluminum rods (Eai = 10E6 psi) are held together by a fixed support on the left and a…

A: The detailed solution is given below.

Q: Given the figure shown below, bronze and aluminum compound shaft are attached to rigid supports. The…

A: To find: The maximum torque carried by the aluminum shaft. Given: The diameter of bronze shaft is…

Q: • Q-2 Figure gives the cross section of a grade 25 cast-iron pressure vessel. A total of N bolts are…

A: Given: No:25 CI M16×20×60mm class 5.8 H=14.8mm…

Q: Calculate the maximum stress affecting a bolt by specifying which Bolts will have the maximum stress…

Q: A 5⁄8-inch-thick tension member is connected to two 1⁄4-inch splice plates, as shown in Figure The…

A: Bolts are in double shear ϕrn=24.9 kips/bolt {from the manual table 7-1} The required strength…

Q: SITUATION III. For Items 13-14. Refer to figure 7. 60 kips The cast iron block with cross-sectional…

Q: A butt connection is shown in the following figure. Plates is Q235 steel; 8.8 Grade M16 high-…

A: Load bearing capacity Loadbearing capacity is the maximum ability of a structural member or…

Q: The steel bar in the figure has a hollow circular cross-section (dais = 111 mm, tooth = 85 mm), one…

A: The expression for the buckling load, one side hinged and one side is shown below.

Q: Q-1 A steel bar of thickness h, to be used as a beam, is welded to a vertical support by four fillet…

Q: figure is attached to a shaft with a diameter of d=50mm with a welded seam closed on both sides with…

A: Given:F=8 kNd=50 mm or 0.05 mr=d2=502=25 mm or 0.025 ma=4 mm or 0.004 mτ=180 N/mm2

Q: A rectangular plate of width b-40 mm and thickness s 20 mm has a hole with a diameter d=8 mm in the…

A: Given:b=40 mms=20 mmd=8 mmF=15000 NFor dw=840=0.2;From the graph:Kf=2.5Stress developed without…

Q: For the figure shown, use P = 100 kN, L = 300mm, 5 = 100 mm and S2 = 180 mm. Assume the diameter of…

A: Ans: 14. b 15. d 16. a

Q: A M12 x 1.25 hex-head bolt with a nut is used to clamp two 25-mm thick steel plates. The nut height|…

A: Give:- At=84.3 mm2 F=12 kN To find:- g) Stress in bolt

Q: details are given, rivets and plates. Find the maximum shear, crush and tear (tensile) stresses.…

Q: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a thickness…

Q: A knuckle joint, that shown in the figure below, is used to transmit 250 kN. Considering the various…

A: Knuckle joint is defined as when there is a small amount of flexibility in joining the two rods with…

Q: m2. your con

Q: A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: (i) Stess at secion X-Xσ=P(b-ϕn)A=1000 X 103(100-25) X 12σX-X=111.1MPawhere b and T→ width and the…

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

Q: Calculate the maximum stress in the steel ring if a copper ring with a thread diameter of 2000 mm…

A: Given,

Q: A copper [E = 104 GPa, a = 17.1x10-6/°C] rod (2) is placed within a steel [E = 208 GPa,…

Q: S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B…

Q: A steel rod with a cross sectional area of 120mm2 is stretched between two fixed points. The tensile…

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

Q: The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve. The outer diameter of…

Q: A mild steel rod is subjected to a design stress of 382.16 N/mm2. If the maximum allowable stress is…

A: given data:- design stress (Sd)=382.16 N/mm allowable working stress(Sw)=500 mpa…

Q: Solid steel post subjecting torsion. Given that the diameter is 75.05 mm, length is 2.5.05 m and…

A: Given Diameter, d = 75.05 mm Length, L = 2.5 m Shear modulus, G = 78.08 GPa Torque, T = 540 N-m…

Q: S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B…

A: given data; ⇒carry load(P)=100KN =100*103N⇒torque(T)=250 N-mm2⇒stress(σ)=350…

Q: 3. Problem 2: The lap joint is fastened with four rivets. If the working stress is 14 ksi (kips per…

Q: Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a…

Q: 1. An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm2. If the cylinder…

Q: The bracket shown in Figure ST - 228 is attached to a column by 6 - 20 mm diameter bolts and loaded…

A: The bearing stress between the bolt and the bracket is 61.46 MPa.

Q: The plunger of an oil pump is held against the operating cam by a spring made of No.10 W&M gage…

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

A: Find , Allowable load F.

Q: The figure below shows the shaft of an overhang crank subjected to a force P of 3.5kN. The shaft is…

Q: 12 in 14-in D -in R. 2 in C 1-in D. 15 in 1-in D. Figure (2-1) A stress element at A on the top…

A: For solution refer below images.

Q: Ql: For the problem in Figure (1), determine maximum allowable load P such that maximum flexural…

Q: The cantilever bar in the figure is made from a ductile material and is statically loaded with Fy=…

Q: Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a…

Q: Q-1 The attachment shown carries a static bending load of 15 kN. The attachment length, 4, is 260…

A: Static bending load acting is 15 kN Attachment length 260 mm

Q: A cylindrical bar shown in the figure below has axial loads applied as illustrated. Calculate the…

A: As per given We have to find stress in bar of section AB, BC and CA

Concept explainers

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.

Question

Can you please complete the following just need help with the question as it's my last to do.

The 10-mm-diameter steel bolt in (Figure 1) is surrounded by a bronze sleeve . The outer
diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. Est = 200 GPa,
Ebr = 100 GPa.
Figure
1 of 1
P
-10 mm
- 20 mm
P
------ ----- ---

Part A
If the bolt is subjected to a compressive force of P = 15.3 kN, determine the average normal stress in the steel.
Express your answer to three significant figures and include appropriate units.
HA
?
Ost =
Value
Units
Submit
Request Answer
Part B
If the bolt is subjected to a compressive force of P = 15.3 kN, determine the average normal stress in the bronze.
Express your answer to three significant figures and include appropriate units.
HẢ
?
Value
Units
Obr
Submit
Request Answer
< Return to Assignment
Provide Feedback

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
A steel plug has a diameter of 20 mm at 30 °C. At what temperature will the diameter be equal to 19.995 mm? a=11 x 10-6 /°C. A) -23.57 celcius B) -5.53 celcius C) 7.27 celcius D) 52.73 celcius
Determine the thickness of a steel air receiver with 30 inches diameter and pressure load of 120 psi with a design stress of 8,000 psi. A. ¼ in C. 3/8 inB. 5/8 in D. ½ in
What will be the minimum diameter of a steel wire, which is used to raise a load of 4000N if the stress in the rod is not to exceed 95 MN/m²?
Two rods are connected to each other and are restrained at top and bottom. The top portion is steel with modulus of elasticity equal to 200x10^3 MPa and coefficient of thermal expansion equal to 11.7x10^-6/C, the bottom is made up of brass with modulus of elasticity equal to 105x10^3 MPa coefficient of thermal expansion equal to 20.9x10^-6/"C. The temperaturé rose to 50°C from normal condition introducing stresses in the bar. Determine the force induced in the bar. Note: Final Answer in 4 decimal places.
....A 150-mm diameter shaft supports a load of 12 kN. The shaft runs in a bearing whose length is 1.5 times the shaft diameter. Which of the following is the bearing pressure? Group of answer choices 0.127 MPa 0.296 MPa 0.356 MPa 0.170 MPa
Calculate the maximum stress in the steel ring if a copper ring with a thread diameter of 2000 mm and a thickness of 20 mm and a steel ring with an inner diameter of 2000 mm and a thickness of 10 mm are interlocked and heated to 100°C. Scale= 100 GPa, Eçelik= 200 GPa, copper= 16.106/°C, steel= 12.10-6/°C a-) 20 MPa b-) 40 MPa c-) 50MPa d-) 60 MPa e-) 30 MPa
A steel bolt is subjected to a tensile load of 45 kN and shear stress of 25 MPa.Calculate the maximum stress induced on the bolt if its diameter is taken as 30 mm.a. 40.47 MPab.63.66 MPac. 64.88 MPad.72.31 MPa
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figures
A tensile load of 330,000 N is applied to a copper pipe with maximum allowable stress of 110 MPa and 80 mm inner diameter. What should be the thickness of the pipe? Choices: A. 9.78 mm B. 12.35 mm C. 11.56 mm D. 10.55 mm
Calculate the safety of the cylinder pivot pin in relation to the yield. The tensile yield strength of the pin material is ReL=600MPa. The dimensions of the structure are: x1 = 10 mm x2 = 120 mm y1 = 110 mmy2 = 798 mm Piston rod = φ32mm Cylinder pivot pin = φ25mm Pliers pivot pin = φ30mm The clamping force of the pliers is 6000N Answer to one decimal place !!
A 0.5-in.-diameter steel [E= 30,000 ksi] bolt (1) is placed in a copper tube (2). The copper [E= 16,000 ksi] tube has an outside diameter of 1.00 in., a wall thickness of 0.125 in., and a length of L= 8.0 in. Rigid washers, each with a thickness of t= 0.125 in., cap the ends of the copper tube. The bolt has 20 threads per inch. This means that each time the nut is turned one complete revolution, the nut advances 0.05 in. (i.e., 1/20 in.). The nut is hand-tightened on the bolt until the bolt, nut, washers, and tube are just snug, meaning that all slack has been removed from the assembly but no stress has yet been induced. What stresses are produced in the bolt and in the tube if the nut is tightened an additional quarter turn past the snug-tight condition?