The 11-kg block is attached to the massless link AB and rests on a belt as shown. Determine the magnitude of the horizontal force F (in Newton) required to maintain the motion of the belt to the right. Consider 22 degrees. = Hint: You need to draw the FBD of the belt as a part of your solutions. Hs=0.40 Mk = 0.30 A F e B

The 11-kg block is attached to the massless link AB and rests on a belt as shown. Determine the magnitude of the horizontal force F (in Newton) required to maintain the motion of the belt to the right. Consider 22 degrees. = Hint: You need to draw the FBD of the belt as a part of your solutions. Hs=0.40 Mk = 0.30 A F e B

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.20P: The 3600-lb car with rear wheel drive is attempting to push the 4500-lb crate. The center of gravity...

See similar textbooks

Similar questions

Find the stable equilibrium position of the system described in Prob. 10.56 if m = 2.06 kg.
The 3600-lb car with rear wheel drive is attempting to push the 4500-lb crate. The center of gravity of the car is at G, and the coefficients of static friction are 0.6 at B and 0.2 at C. Determine if the crate will slide. (The car pulling the crate is analyzed in Prob. 7.19.)
Determine the largest angle for which the homogeneous block remains at rest.
The 80-kg crate has its center of gravity at G. Determine the smallest force P that will initiate motion if =35.
The cylinder having a diameter 2.5 ft weighs 57 lb and is 6 ft long. Determine the reaction (lb.) at A neglecting friction. Determine the reaction at B (lb.) neglecting friction. Weight density of water is 62.4 lb/ft3 Sp.gr Gs = 1.6
Determine the magnitude and direction of the angle theta of the force FAB that must be exerted on bar AB to maintain equilibrium of the system. The suspended mass is 110 kg. Neglect the size of the pulley at A and treat all pulleys as smooth. What should happen to maintain the equilibrium of the system if FAB acts with an angle theta= 0°?Consider g = 9.81 m/s2.
the man is holding up the 35-kg ladder ABC by pushing perpendicular to ladder. The total length of the ladder is AC=6m. If maximum force that the man can exert is 400N at B which is 2m from A. determine the smallest angle, theta, at which the man can support the ladder
If cylinder E has a mass of 20 kg and each cable segment can sustain a maximum tension of 400 N, determine the following: 3.1 The largest mass of cylinder F that can be supported by the system is ______ kg. 3.2 The sag yC is equal to ______ m.
If the mass of cylinder C is 40 kg, determine the mass of cylinder A in order to hold theassembly in the position shown in the figure.
If the block remains in the equilibrium position shown, determine the mass of the block D. The unextended length of spring AB is 9 m. d1 = 8 m d2 = 10 m KAC = 44 N/m KAB = 70 N/m Mass of block D = ____ kg
Determine the maximum force P that can be applied withoutcausing the two 50-kg crates to move. The coefficient of staticfriction between each crate and the ground is s = 0.25.(Use g = 9.81 m/s2) P =
The smooth disks D and E have a weight of 200 lb and 100 lb, respectively.a. Determine the largest horizontal force P that can be applied to the center of disk E without causing the disk D to move up the incline. b. Determine also the reactions (NA, NB, and NC) at the contact surfaces. Assume smooth surfaces.