The 15 kg pendulum shown has its mass center at G and a radius of gyration about its mass center of kG = 200 mm and was released from rest when 0 = 0° . Spring AB has a stiffness of k = 200 N/m and is un-stretched when e = 90° . The angular velocity of the pendulum in rad/s at the instant e = 90° is: -0.6 m- а 3.2

The 15 kg pendulum shown has its mass center at G and a radius of gyration about its mass center of kG = 200 mm and was released from rest when 0 = 0° . Spring AB has a stiffness of k = 200 N/m and is un-stretched when e = 90° . The angular velocity of the pendulum in rad/s at the instant e = 90° is: -0.6 m- а 3.2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 100-kg spool is resting on the inclined surface for which the coefficient of kinetic friction is μk = 0.11. The radius of gyration about the mass center is kG = 0.26 m Determine the angular velocity of the spool, measured clockwise, when t = 7 s after it is released from rest.
The slotted circular disk whose mass is 4.9 kg has a radius of gyration about O of 230 mm. The disk carries the four steel balls, each of mass 0.17 kg and located as shown, and rotates freely about a vertical axis through O with an angular speed of 164 rev/min. Each of the small balls is held in place by a latching device not shown. If the balls are released while the disk is rotating and come to rest relative to the disk at the outer ends of the slots, compute the new angular speed N of the disk. Also find the magnitude |ΔE| of the energy loss due to the impact of the balls with the ends of the slots. Neglect the diameter of the balls and discuss this approximation.
The pendulum has a mass of 8.8 kg, a centre of gravity at G, and a radius of gyration of 0.31 m about the fixed pin support at O. At what position (in degrees) must the pendulum by released from rest so that its angular acceleration is 18.6 (clockwise) at that instant? Take = 0.25 m. The motion occurs in a vertical plane and friction is negligible. Choose the correct answer. 43.2 36.7 34.6 48.4 41.1
The body and bucket of a skid steer loader has a weight of 2000 lb, and its center of gravity is located at G. Each of the four wheels has a weight of 100 lb and a radius of gyration about its center of gravity of 1ft. If the engine supplies a torque of M = 100 lb ft to each of the rear drive wheels, determine the speed of the loader in t = 10 s starting from rest. The wheels roll without slipping
The 30-kg turbine disk has a centroidal radius of gyration of 175 mm and is rotating clockwise at a constant rate of 60 rpm when a small blade of weight 0.5 N at point A becomes loose and is thrown off. Neglecting friction, determine the change in the angular velocity of the turbine disk after it has rotated through (a ) 90°, (b ) 270°.
The thin 12 kg bar has an angular velocity in a clockwise direction ω = 1.5 rad/s when in position shown. Determine its angular acceleration and the normal reactions of the smooth surface A and B at that time. i = (1/12) M . L² for a homogeneous thin bar of mass M and length L.
The differential pulley C, which rotates as a unit, has a mass of 14.1 kg, an inner radius of 75 mm, an outer radius of 150 mm, and a radius of gyration of 100 mm about its stationary centre of gravity at O. Each cylinder (A and B) has a mass of 18.6 kg. At the instant shown, the light cables do not slip and cylinder A has a velocity of vA= 2.5 m/s (downwards). The motion occurs in a vertical plane. What is the total kinetic energy of the system at this instant? Choose the correct answer. a) 78.4 Joule b) 87.6 Joule c) 73.8 Joule d) 55.3 Joule e) 92.2 Joule
The slender L-shaped bar ABCD mass 15 kg/m is free to rotate about thepin at B. The spring connected to the bar at A has a free length of 7 ft, and itsstiffness is 180 N/m. If the system is released from rest in the position shown,determine the angular velocity of the bar when A is directly above B.
The assembly weighs 10 lblb and has a radius of gyration kGkGk_G = 0.60 ftft about its center of mass GG. The kinetic energy of the assembly is 25 ft⋅lbft⋅lb when it is in the position shown. (Figure 1) If it rolls counterclockwise on the surface without slipping, determine its linear momentum at this instant.
The rod AB has a mass of 20 kg，the mass of the piston A and B are both 5kg. Piston B is attached to a spring of constant k = 1200 N/m. The spring is un-stretched when θ = 0. If the rod is released from rest whenθ = 45° Please find÷ (1) the moment inertia of the rod AB about its mass center G (2)The angular velocity of rod AB at θ = 0° (3）the velocity of piston A at θ = 0° (4) the velocity of Piston B at θ = 0° (hint: regard the piston A, B, rod as a system, during the motion, except the spring, the weight of rod AB, the weight of pistonB also does work). g = 9.8 m/s2
if mass (m)=345kg radius of gyration kG = 0.54 m θ= 200 degree 1) assuming no slipping and when starting from horizontal cable (θ = 0o) the spool moves to the left- determine the minimum tension in the cable (Tmin) that causes the spool to slip. Assumeμk = 0.4 and μs = 0.5.
The 153-kg wheel has a radius of gyration about its center of mass O of kO = 283 mm. If it rotates counterclockwise at an angular speed of 1431 rev/min and the tension force applied to the braking band at A is TA = 1771N,a) Determine the angular acceleration, in rad/s2, so that the wheel comes to rest in 67.6 revolutions after TA and TB are applied.