(1) The uniform slender bar of mass m = 9.6 kg and length L = 0.5 m has small end rollers. Roller A is free to slide on the horizontal floor B and B is a free roller. The rod is released in the position shown where 0 = tan (3/4) with an initial clockwise angular velocity w = 4 rad/s . Determine the normal force N under roller A immediately after release. Ans: 30.5 N

(1) The uniform slender bar of mass m = 9.6 kg and length L = 0.5 m has small end rollers. Roller A is free to slide on the horizontal floor B and B is a free roller. The rod is released in the position shown where 0 = tan (3/4) with an initial clockwise angular velocity w = 4 rad/s . Determine the normal force N under roller A immediately after release. Ans: 30.5 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

*********MASS IS 10 KG, NOT LBS********** The 10 kg slender bar AB, shown in the figure, has a length of 2 m. A blockof negligible mass, pinned freely to end A, is confined to move along the smooth circular groove with its centre at O. End B rests on the floor for which the coefficient of kinetic friction, µk = 0.4. If the bar is released from rest when θ = 30 degrees *********MASS IS 10 KG, NOT LBS********** a)draw the free body, kinematic and kinetic diagrams for the bar, b) set up a global reference axes system, and write down the relevantkinetic and kinematic relationships with respect to reference axes system, and c) determine the angular acceleration of the bar and the reaction forces at ends A and B. *********MASS IS 10 KG, NOT LBS**********
In the figure, the hanging object has a mass of m1 = 0.420 kg; the sliding block has a mass of m2 = 0.850 kg, and the pulley is a hollow cylinder with a mass M = 0.350 kg, a interior radius R1 = 0.0200 m and an exterior radius R2 = 0.0300 m. Assume that the mass of the rays is negligible. The coefficient of kinetic friction between the block and the surface horizontal is µk = 0.250. The pulley rotates without friction on its axis. The lightweight cable does not stretch and does not slip on pulley. The block has a velocity of vi = 0.820 m / s towards the pulley when you pass a landmark on the table. (a) Use energetic methods to predict its velocity after it has passed a second point, which is at 0.700 m. (b) Find the angular speed of the pulley at the same moment.
Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
A small 2-lb ball B is rotating (Fig.13) at angular speed w1 of (6+(0.1*26)) rad/sec about a horizontal shaft. The ball is connected to the bearings with light elastic cords which when unstretched are each 12 in. in length. A force of 15 lb is required to stretch the cord. The distance d1 between the bearings is originally 20 in. If the bearing A is moved to shorten d by 6 in, what is the angular velocity w2 of the ball? Neglect the effects of gravity and the mass of the elastic cords. Use the moment of momentum equation.
Derive the equation of motion for the homogenous shaft and disc system. if the disc mass is 50 kg, the shaft radius is 0.1 m,the torsional spring constant 75N/m and length of shaft is 0.5m and rigidity of shaft material is (G = 80.7GPa). Determine the θ as function of time if the disc is released from rest at the position θ = 10 rad at time t=0 (Jo = 0.5 m * r²)
A motorcycle and rider have a combined mass of 350kg. The each wheel has a mass of 20kg with the diameter of 500 mm. The rider accelerates from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. Identify the magnitude and effect of gyroscopic reaction torque by calculating the angular velocity and power as the motorcycle ascends the incline when the motorcycle and rider travel at 80 km/h around a left-hand bend of road with the radius 30 m.Explain the effects of energy transfer in mechanical systems (e.g. gears, pulley or flywheel) with uniform acceleration present.
The 10 kg slender bar AB, shown in the figure, has a length of 2 m. A blockof negligible mass, pinned freely to end A, is confined to move along the smooth circular groove with its centre at O. End B rests on the floor for which the coefficient of kinetic friction, µk = 0.4. If the bar is released from rest when θ = 30 degrees a) draw the free body, kinematic and kinetic diagrams for the bar, b) set up a global reference axes system, and write down the relevantkinetic and kinematic relationships with respect to reference axes system, c) determine the angular acceleration of the bar and the reaction forces at ends A and B. *****MASS IS 10KGS NOT 10LBS*****
A force was applied to a 50 kg wheel as shown in the figure. If the wheel starts to rest without slipping Determine the angular acceleration ε, the wheel pressure on the ground N and the rotational speed of the wheel n after 10 revolutions, if the rolling friction coefficient f = 0.1. Take the radius of inertia of the wheel equal to 0.3 m.
A cylinder of mass M=500kg has an axle of radius b=1m and a spool of radius R=3m. It is placed upright on a table and the string is pulled with a horizontal force F=750N to the right as shown in the figure. The cylinder is rolling without slipping and the coefficient of static friction between the cylinder and the table is µs =0.34. I = 1/2 MR^2a. Determine the linear velocity of the cylinder when it travels a distance D=2m. c. Determine the linear acceleration of the cylinder. d. Determine the friction force acting on the cylinder. e. What is the maximum pulling force, F, for which the cylinder will roll without slipping.
The slender, homogeneous rod shown in the figure below is 3 m in length and has a mass of 12 kg. At the instant shown, the rod has an angle to the horizontal of 60-degrees and an angular velocity of 2 rad/s clockwise. Both walls are smooth and provide negligible friction. At the instant shown, what are the reaction forces at A and B? What is the angular acceleration of the rod's center of mass?
The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. Ignore the spring's mass. (1) If the datum for gravitational potential energy is set as shown below, the the gravitational potential energy of the wheel at the state 1 is___ N m(two decimal places) (2) If the datum for gravitional potential energ is set as shown below, the gravitational potential energy of the wheel at the state 2 is___ N m (two decimal places) (3) At state 1, how long the spring is stretched from its unstretched state (length difference):________(m) (two decimal places) (4) The…
The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. Ignore the spring's mass. (5) At state 2, how long the spring is stretched from its unstretched state (length difference):________(m) (two decimal places) (6) The elastic potential energy of the spring at the state 2 is_______(N·m) (two decimal places) (7) The instantaneous center of zero velocity (IC) of the wheel at state 1 is (8) The mass moment of inertial of the wheel about its mass center G is IG =_________(kg·m2 ) (two decimal places)