The 25-kg block A is released from rest. (Figure 1) Figure B A < 1 of 1 > Part A Determine the velocity of the 15-kg block B in 2 s. Express your answer to three significant figures and include the appropriate units. Enter positive value if the velocity is upward and negative value if the velocity is downward. V HÅ Value Units Submit Provide Feedback Request Answer www ? Next >

The 25-kg block A is released from rest. (Figure 1) Figure B A < 1 of 1 > Part A Determine the velocity of the 15-kg block B in 2 s. Express your answer to three significant figures and include the appropriate units. Enter positive value if the velocity is upward and negative value if the velocity is downward. V HÅ Value Units Submit Provide Feedback Request Answer www ? Next >

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 38P

See similar textbooks

Similar questions

28. Situation 10 - An object (SG = 7.3) floats in mercury (SG = 13.6) such that a certain portion is above the liquid surface. a. What fraction of the volume of the object floats above the surface of the mercury? Round off to three decimal places. b. If the volume of the object below the liquid surface is 0.014 m3, what load, in kN, applied vertically that would cause the object to be fully submerged? Round off to two decimal places. c. If the volume of the object below the liquid surface is 0.014 m3, what is the weight, in kN, of the object? Round off to two decimal places.
1. In calibrating a 10-mL pipet, a measured volume of water was transferred to a tared flask and weighed, yielding a mass of 9.9814 g. (a) Calculate, with and without correcting for buoyancy, the volume of water delivered by the pipet. Assume that the density of water is 0.99707 g/cm3 and that the density of the weights is 8.40 g/cm3. (b) What are the absolute and relative errors introduced by failing to account for the effect of buoyancy? Is this a significant source of determinate error for the calibration of a pipet? Explain. 2. Repeat the questions in problem 1 for the case when a mass of 0.2500 g is measured for a solid that has a density of 2.50 g/cm3. 3. Is the failure to correct for buoyancy a constant or proportional source of determinate error?
An elevator weighing 9.8 KN moves downward from rest until itattains a velocity of 20 m/s after it travels a distance of 5 m. Whatis the travel time of the elevator at this instant?a. 3 secsb. 2 secsc. 1 secd. 0.5 sec
answers should be in 3 decimal places The rotation of a flywheel is defined by the rotation ω = 2(4t + 1)1/2, where ω is in rad/sec and t in sec. When t =0, θ = 4 rads. 1. Find the value of θ when t = 5 secs. 2. Find the value of α when t = 5 secs.
A ball is thrown straight upward from the ground level. Its initial velocity is 30 m/s. 1. What is the maximum height it reaches in meters? a. 13.98 b. 45.87 c. 10.38 d. None of these 2. What is the total time in seconds when it goes back in the ground? a. 3 b. 6 c. 4 d. None of these
The water system in a suburban area consists of an old 200mm pipeline 760m long which conveys water from a pump to a reservoir whose water surface is 107m higher than the pump. Water is pumped at the rate of 0.07 m3/s. Determine the horsepower saved by replacing the old pipe with a new 250mm pipe. Assume the value of f as equal to 0.022 and 0.033, respectively, for the old and new pipes. Neglect losses of head except friction head show the diagram and complete solution. Need ASAP. Thank you
19. Situation 7 - Three pipes are connected in series. The first pipe has a diameter of 500 mm and a length of 600 m. The second pipe has a diameter of 400 mm and a length of 500 m. The third pipe has a diameter of 300 mm and a length of 200 m. Use f = 0.02 for all pipes. If Q=0.8 m^3/s, a. What is the equivalent diameter, in mm, of a single pipe having the same properties that could replace the three pipes? Round off to the neares whole number. b. What is the total head loss, in meters, from pipe 1 to pipe 3? Round off to three decimal places. c. What is the total head loss, in meters, in pipe 1? Round off to three decimal places.
A smooth steel (SG = 7.86) sphere is immersed in a streamof ethanol at 20 ° C moving at 1.5 m/s. Estimate its drag inN from Fig . What stream velocity would quadrupleits drag? Take D = 2.5 cm.
A 2x3 ft cylindrical drum is filled with a fluid whose density is 40 lb/ft3 . Determine (a) the totalvolume of the fluid, (b) its total mass in pounds and slugs, (c) its specific volume, and (d) its specificweight where g = 31.9 fps2
Show all problem solution's steps. Direct formula substitution solutions will have NO CREDIT POINTS. 1. A 75 mm diameter fire hose discharges water through a nozzle having a jet diameter of 25 mm. The lost head in the nozzle is 25% of the velocity head in the jet. If the pressure at the base of the nozzle is 625 KPa: compute the discharge in m3/min; the maximum horizontal range to which the stream can be thrown; the maximum vertical reach, and the diameter of the jet at a point two-third of the maximum vertical reach from the tip of the nozzle. Neglect air resistance.
. A pump draws water from a reservoir and conveys it to another reservoir 30 m above. The sucLon pipe is 100 mm in diameter and 10 m long while the delivery pipe is 100 mm in diameter and 150 m long. if the velocity in the pipe is 3 m/s, the fricLon factor of the pipe 0.008, and the pump and motor efficiencies 85 % and 92 %, respecLvely. See Figure Q6.1. Calculate:(a) Gauge pressure at the pump's inlet (at C) (10)(b) Gauge Pressure at the pump's outlet (at D) (10)(c) input power to motor (5)
An open circular vessel is 1m in diameter and 2m height. It contains water filled to a depth of 1.5m. If the cylinder rotates about its vertical axis, what constant angular velocity can be obtained without spilling? Unit of the Correct Answer: rad/sec Decimal Places required in the final answer: 3 PLS 3 DECIMALS..