The 3-phase transmission line parameters are given bellow. 1. Receiving end power 40 MW, 2. Receiving end voltage 250 kV 3. Receiving end PF 0.65 lagging. 4. Sending end voltage 335kV. 5.The value of constant A is 0.9. Find Receiving end power /Phase in MW Receiving end voltage /Phase in kV Receiving end current I, in Amps

The 3-phase transmission line parameters are given bellow. 1. Receiving end power 40 MW, 2. Receiving end voltage 250 kV 3. Receiving end PF 0.65 lagging. 4. Sending end voltage 335kV. 5.The value of constant A is 0.9. Find Receiving end power /Phase in MW Receiving end voltage /Phase in kV Receiving end current I, in Amps

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.25P

See similar textbooks

Similar questions

The 500-kV, 60-Hz, three-phase line in Problems 4.20 and 4.41 has a 180-km length and delivers 1600 M W at 475 kv and at 0.95 power factor leading to the receiving end at full load. Using the nominal circuit, calculate the (a) ABCD parameters, (b) sending-end voltage and current, (c) sending-end power and power factor, (d) full-load line losses and efficiency, and (e) percent voltage regulation. Assume a 50C. conductor temperature to determine the resistance of this line.
A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
A 30-km, 34.5-kV, 60-Hz, three-phase line has a positive-sequence series impedance z=0.19+j0.34/km. The load at the receiving end absorbs 10 MVA at 33 kV. Assuming a short line, calculate: (a) the ABCD parameters, (b) the sending-end voltage for a load power factor of 0.9 lagging, and (c) the sending-end voltage for a load power factor of 0.9 leading.
A 200-km, 230-kV, 60-Hz, three-phase line has a positive-sequence series impedance z=0.08+j0.48/km and a positive-sequence shunt admittance y=j3.33106S/km. At full load, the line delivers 250 MW at 0.99 p.f. lagging and at 220 k V. Using the nominal circuit, calculate: (a) the ABCD parameters, (b) the sending-end voltage and current, and (c) the percent voltage regulation.
The 100-km, 230-kV, 60-Hz, three-phase line in Problems 4.18 and 4.39 delivers 300 M VA at 218 kv to the receiving end at full load. Using the nominal circuit, calculate the ABCD parameters, sending-end voltage, and percent voltage regulation when the receiving-end power factor is (a) 0.9 lagging, (b) unity, and (c) 0.9 leading. Assume a 50C conductor temperature to determine the resistance of this line.
The following parameters are based on a preliminary line design: per unitVS=1.0, VR=0.9 per unit, =5000km,Zc=320,=36.8. A three-phase power of 700 MW is to be transmitted to a substation located 315 km from the source of power. (a) Determine a nominal voltage level for the three-phase transmission line, based on the practical line-loadability equation. (b) For the voltage level obtained in part (a), determine the theoretical maximum power that can be transferred by the line.
Transmission line conductance is usually neglected in power system studies. True False
A three-phase overhead transmission line is designed to deliver 190.5 M VA at 220 kV over a distance of 63 km, such that the total transmission line loss is not to exceed 2.5 of the rated line MVA. Given the resistivity of the conductor material to be 2.84108-m, determine the required conductor diameter and the conductor size in circular mils. Neglect power losses due to insulator leakage currents and corona.