5 The 9-m boom AB is acted upon by the 5.7 kNforce as shown in figure. Determine the tensionin cable BD.4 m2.5 m2 m1.8 mB.4.5 m5.7 ktl4.5 mEsalons E2 pdfTension 48 2 KNTension=47 KNTenslon= 0E KN

Answered: Image /qna-images/answer/a3193fe8-e54e-4a73-b09b-d718933e9cec.jpg

Answered: The 9-m boom AB is acted upon by the…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.153P: Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.

See similar textbooks

Similar questions

Find the support reacions and joint force of the construction shown on the figure, if; P=12 kN q=9 kN/m M=12 kN and L=2 m
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
4.00 kg block is attachedto a vertical rod by meansof two strings. When the systemrotates about the axis of the rod,the strings are extended as shownin Fig. and the tensionin the upper string is 80.0 N. (a)What is the tension in the lowercord? (b) How many revolutionsper minute does the system make?(c) Find the number of revolutionsper minute at which the lowercord just goes slack. (d) Explainwhat happens if the number ofrevolutions per minute is less thanthat in part (c).
an arrangement inwhich four disks are suspended by cords.Thelonger, top cord loops over a frictionless pulleyand pulls with a force of magnitude 98 Non the wall to which it is attached.The tensionsin the three shorter cords are T1 = 58.8 N,T2 = 49.0 N, and T3 = 9.8 N. What are themasses of (a) disk A, (b) disk B, (c) disk C,and (d) disk D?
The bent bar ABD is supported by a ball joint at D and a bearing at A, and a rope at B. A mass of 100 kg is supported at E, as shown in the figure. Knowing that the bearing at A exerts forces only in the “z” and “y” directions, find the tension in chord BC. (TBC = 572 N)
Th lamp , mass = 10 Kg, is suspended in the position shown. The undeformed length of spring AB is 0.84 m and the spring has a stiffness of K = 784 N/m. For L= 2.8 m find Tension in cable AC , Internal force in spring AB, length of AC
a=(3.7m) , b=(3.7m) ,theta =(33) , p1=(3.7)KN , p2=(2.4)KN find the forces in each members and idicate also the tension or compression
Please reply as soon as posible, thanks! I don´t have much time:( Static Problem: The spool shown in the figure has a weight of WAB = 27,50 N, and its center of gravity is located at its geometric center O, the spool has a larger radius R=0,17 and an inner radius r=0,13, and it has a coiled rope. Block C has a uniform weight WC= 60 N. Consider the friction between block C and the top of the spool at A, between the spool and the surface at point B and between the rope and pulley D, the friction coefficients are respectively: μs@A=0,30, μs@B =0,45 and μs@D=0,35. The chord is parallel to the plane. Carry out: a) The free-body diagrams of the block and the reel. b) The calculation of the maximum value of P that can be applied without losing the equilibrium of the system.
Three cylinders are piled up in a rectangular channel as shown in the figure. Determine the reactions at the all the points of contact. Cylinder A:Radius=4cm ,m=15kg Cylinder B:Radius=6cm,m=40 Kg Cylinder C: Radius = 5cm,m= 20kg
2-D PROBLEM: A spherical tank with a radius of 3.41m that has a mass of 28928.644kg was supported in the system shown. Assuming friction and the bar weight is negligible, determine the following: β: 21.774° θ: 46.452° 1. The reaction @ point D. 2. Tension @cable BE 3. The x and y-component of the reaction @ A 4. The reaction @ A
A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0,respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the leftend where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) andthe weight (W) of the bar
A rotating drum is braked by a flat belt attached to the lever ABC, hinge at B as shown in Figure. Determine the braking moment exerted by a vertical weight of 150 N. Take AB = 35 cm, BC = 65 cm and coefficient of friction between the belt and drum surface is 0.43. The radius of the drum is 0.2 m OPTIONS: 1.About 35 N-m 2.None 3.About 40 N-m 4.About 50 N-m 5.About 30 N-m 6.About 45 N-m

SEE MORE QUESTIONS

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The 9-m boom AB is acted upon by the 5.7 kN force as shown in figure. Determine the tension in cable BD. 4 m 2.5 m 2 m 1.8 m 4.5 m 5.7 kt 4.5 m Tension = 482 KN Tension4.7 kN Tenslon= 0 5 KN