The beam is acted upon by force F = 17 kN as shown in the figure. What is the shear force in section C in kN. Find the moment of area of the fiber 30 mm above the bottom of the beam about the neutral axis in mm3. find the shear stress in MPa at a point 30 mm above the bottom of the beam at secti

The beam is acted upon by force F = 17 kN as shown in the figure. What is the shear force in section C in kN. Find the moment of area of the fiber 30 mm above the bottom of the beam about the neutral axis in mm3. find the shear stress in MPa at a point 30 mm above the bottom of the beam at secti

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter4: Shear Forces And Bending Moments

Section: Chapter Questions

Problem 4.3.5P: Consider the beam with an overhang shown in the figure. Determine the shear force V and bending...

See similar textbooks

Related questions

Q: H.W 3_ Two aluminum alloy plates (2) are attached to the sides of a wooden beam (1) as shown in…

Q: * Given: Maximum shear FORCE=13 KN, and moment of inertia = 120 x 10^6 mm^4. Find the maximum shear…

Q: The dimensions of the beam with the cross-section are given as b, a, t as in the figure on the…

A: Given data The dimensions of the beam with the cross-section are given as b, a, t as in the figure…

Q: Q4) The figure below shows the shear force diagram of a beam with their cross-section. a) Find the…

A: As you have posted a multiple question, we are supposed to answer the first 3 subparts of the first…

Q: Q4: If the cross section of the beam shown in the figure (3) below has bending stress of 28 MN/m² in…

Q: The vertical shear force acting in a beam with the cross section shown in the figure is 20 kips.…

Q: In figure below, the shear force (Q) is equal to 150 kN. What is the shear stress (t) at the neutral…

Q: Two uniformly distributed loads w = 4200 lb/ft of act on the simply supported beam shown in Figure…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: a) Find the maximum normal stress and maximum shear stress. b) Compare these values with the…

A: We are to determine the shear stress and normal bending stress for the beam For this we will…

Q: 3 KN/m D B 120 mm YA= 40 mm A. 80 mm 1m 2 m 10 KN 10 KN L= 4 m

Q: (6) For the composite beam shown in the figure, which is bended about a horizontal axis by a couple…

Q: 80 kN 80 kN 90 cm 90 cm N.A. 80 kN 80 kN (a)

A: Since it can be seen from the figure that the loading is symmetrical about the mid-point of the…

Q: situation; a) Maximum normal stress

Q: Since the bending safety stress em = 10 MPa, shear safety stress em = 600 kPa of the rectangular…

Q: A section is under the effect of M (kNm) bending moment which makes 6° with the positive +z axis as…

Q: Rectangular cross-section and width given the loading state in the figure Bending safety stress of…

Q: The beam, which consists of three parts with a vertical cross section as shown in the figure, will…

A: As per the guidelines, I can solve only part (a). For part (b), please re-post in a separate post.…

Q: QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum…

A: Given oblique bending moment(M)= 5kN-m, θ=30° On resolving the components of the BM So the Bending…

Q: applied to the beam in the figure with the notches below and a hole of diameter d in the middle.…

Q: A beam has a cross-sectional area as shown in the first figure. The lõàdš on the Bea moment diagram…

Q: The maximum bending stress at distance 0.5 m from the built-in right hand end in the structural beam…

Q: A simply supported beam (i.e., with a pin support at point A and a roller support at point D) is…

Q: The figure shows a rectangular section beam with a distributed load of 3 KN/m. Decide: The maximum…

A: Consider a beam having Area Moment of Inertia I and Young's modulus E is subjected to bending moment…

Q: Cross section of a beam is shown in Figure 3. If a shear force V=100 kN is applied to the beam, find…

Q: Q: Find the value of W which can be applied to the beam shown in figure below. if the maximum…

A: Consider the reaction at the supports RB and the reaction at supports C is Rc. Moment about C,…

Q: Cross section of a beam is shown in Figure 3. If a shear force V=100 kN is applied to the beam, find…

Q: For the beam shown in the figure if W- 14 KN/m. Determine the following: 14. The normal force at…

A: (14)

Q: if the cross-section shown in the figure has shear stress of 300psi at point P( located 0.25 in…

Q: 40 N.m Da 0.5 m 280 N.m 150 N.m 2 0.3 m 0.4 m

Q: Half of the beam section shown in the figure is made of aluminum (E) and the other half is made of…

Q: The overhanging beam ABC in Figure supports a concentrated load and a uniformly distributed load.…

Q: The beam in the figure below is made from three boards nailed together as shown, If the internal…

Q: QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum…

A: Cross-sectional view,

Q: Beam cross section is shown in Figure Q3 and given the second moment of area is I= 20.85 x 106 mm*.…

A: Find the shear stress at point M, N, O, P and draw stress distribution over the cross section

Q: For the simply supported beam with square cross sectional area as shown in the figure below: 1.…

A: The summation of force along vertically is given as, ∑Fy=0RA+RB=3 kN+2 kN+5 kNRA+RB=10 kN Taking…

Q: Q.2 A square timber beam used as a railroad tie is supported by a uniformly distributed loads and…

A: Given: ununiform distributed load→W1=24 KN and W2=48 KN Hence upward uniform distributed load:…

Q: 3 kN 100 mm Тop 25 mm 4 kN/m 30 mm 30 mm 100 mm 40 mm B. 6 KN-m -2 m- 3 kN-m 1.5m 18 kN 3 kN

A: Note: As per our company guidelines we are supposed to answer only first three sub-parts. Kindly…

Q: As a result of the loading condition given in the I-section fixed beam shown in the figure;…

A: When a cantilever is applied a point load at the free end it tends to get bend. It will experience…

Q: A column with a wide-flange section has a flange width b = 200 mm , height h = 200 mm , web…

Q: A composite beam is made of two brass [E =101 GPa] plates bonded to an aluminum [E =64 GPa] bar, as…

Q: Q4: If the T- cross section of the beam shown in the Figure (3) below has bending stress of 37 MN/m?…

Q: Q2 The internal bending moment in a beam with a cross sectional area shown in the figure is 500 a in…

A: Given, M= 500 N-m, Now A1=(50+25+50)×25=3125 mm2and area A2=100×35= 3500 mm2 CG of area A1, x1=0,…

Q: Q2, For the composite section beam shown in figure below. Determine the maximum bending stresses.…

A: N = ratio of Elastic modulii= Esteel /Ewood = 10 we will now develop the equivalent beam

Q: beam is loaded as shown in the figure. F = 2200 lb, b = 2 in. and h = 4 in. Determine the…

A: Given data:- Force (F) =2200lb b= 2 in h=4 in

Q: A beam having a cross section in the formof a channel (see figure) is subjected to a bendingmoment…

A: Given Beam ratio = 7:3 To find Magnitude of t

Q: Question 2 Derive the following formula for the distance e from the centreline of the wall to the (2…

Q: For the concentrated load shown in :the figure. find the shear force at RB 50 kN B 10 m For the…

Q: Q.2. A rectangular section 300 mm wide and 500 mm deep is used on a span of 6 m for the loading…

Q: 40 mm 15 mm d-30 mm 20 m

Q: beam section h is at least how much is the height of the beam section in order not to exceed the…

Question

The beam is acted upon by force F = 17 kN as shown in the figure.

What is the shear force in section C in kN.
Find the moment of area of the fiber 30 mm above the bottom of the beam about the neutral axis in mm³.
find the shear stress in MPa at a point 30 mm above the bottom of the beam at section C.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The beam ABC shown in the figure is simply supported at A and B and has an overhang from B to C. The loads consist of a horizontal force P1= 4,0 kN acting at the end of a vertical arm and a vertical force P2= 8.0 kN acting at the end of the overhang, Determine the shear force Fand bending moment M at a cross section located 3,0 m from the left-hand support. Note: Disregard the widths of the beam and vertical arm and use centerline dimensions when making calculations, Find the value of load A that results in V = 0 at a cross section located 2.0 m from the left-hand support. If P2= 8.0 kN, find the value of load P1that results in M = 0 at a cross section located 2,0 m from the left-hand support.
A beam of wide-flange shape, W 8 x 28, has the cross section shown in the figure. The dimensions are b = 6.54 in., h = 8.06 in., fw = 0.285 in., and tf = 0.465 in.. The loads on the beam produce a shear force V = 7.5 kips at the cross section under consideration. Use center line dimensions to calculate the maximum shear stress raiaxin the web of the beam. Use the more exact analysis of Section 5,10 in Chapter 5 to calculate the maximum shear stress in the web of the beam and compare it with the stress obtained in part .
A beam is constructed of two angle sections, each L5 x 3 x 1/2, that reinforce a 2 x g (actual dimensions) wood plank (see the cross section shown in the figure). The modulus of elasticity for the wood is £w = L2 X 106 psi and for the steel is Es= 30 x 106 psi. Find the allowable bending moment M3][cmfor the beam if the allowable stress in the wood is trv= 1100 psi and in the steel is 3 = 12,000 psi. Note: Disregard the weight of the beam, and see Table F-5(a) of Appendix F for the dimensions and properties of the angles.
A plastic-lined steel pipe has the cross-sectional shape shown in the figure. The steel pipe has an outer diameter d1= 100 mm and an inner diameter d2= 94 mm. The plastic liner has an inner diameter d1= 82 mm. The modulus of elasticity of the steel is 75 times the modulus of the plastic. Determine the allowable bending moment Mallowif the allowable stress in the steel is 35 M Pa and in the plastic is 600 kPa. If pipe and liner diameters remain unchanged, what new value of allowable stress for the steel pipe will result in the steel pipe and plastic liner reaching their allowable stress values under the same maximum moment (i.e., a balanced design)? What is the new maximum moment?
A wood beam reinforced by an aluminum channel section is shown in the figure. The beam has a cross section of dimensions 150 mm x 250 mm, and the channel has a uniform thickness of 6.5 mm. If the allowable stresses in the wood and aluminum are 8 M Pa and 38 M Pa, respectively, and if their moduli of elasticity are in the ratio 1 to 6, what is the maximum allowable bending moment for the beam?
A U-shaped cross section of constant thickness is shown in the figure. Derive the following formula for the distance e from the center of the semicircle to the shear center. Also, plot a graph showing how the distance e (expressed as the non dimensional ratio e/r varies as a function of the ratio b/r. (Let b/r range from 0 to 2.)
A W 12 x 50 steel wide-flange beam and a segment of a 4-inch thick concrete slab (see figure) jointly resist a positive bending moment of 95 kip-ft. The beam and slab are joined by shear connectors that are welded to the steel beam. (These connectors resist the horizontal shear at the contact surface.) The moduli of elasticity of the steel and the concrete are in the ratio 12 to 1. Determine the maximum stresses r1 and xtin the steel and concrete, respectively. Note: See Table F-l(a) of Appendix F for the dimensions and properties of the steel beam.
A thin-walled steel tube of rectangular cross section (see figure) has centerline dimensions b = 150 mm and h = 100 mm. The wall thickness t is constant and equal to 6.0 mm. Determine the shear stress in the tube due to a torque T = 1650 N · m. Determine the angle of twist (in degrees) if the length L of the tube is 1.2 m and the shear modulus G is 75 GPa.
A cylindrical pressure vessel having a radius r = 14 in. and wall thickness t = 0,5 in, is subjected to internal pressure p = 375 psi, In addition, a torque T = 90 kip-ft acts at each end of the cylinder (see figure), (a) Determine the maximum tensile stress ctniXand the maximum in-plane shear stress Tmjv in the wall of the cylinder. (b) If the allowable in-plane shear stress is 4.5 ksi, what is the maximum allowable torque T\ (c) If 7 = 150 kip-ft and allowable in-plane shear and allowable normal stresses are 4.5 ksi and 11.5 ksi, respectively, what is the minimum required wall thickness
: A hollow, pressurized sphere having a radius r = 4.8 in, and wall thickness t = 0.4 in. is lowered into a lake (see figure). The compressed air in the tank is at a pressure of 24 psi (gage pressure when the tank: is out of the water). At what depth D0will the wall of the tank be subjected to a compressive stress of 90 psi?
A thin-walled circular tube and a solid circular bar of the same material (see figure) are subjected to torsion. The tube and bar have the same cross-sectional area and the same length. What is the ratio of the strain energy U1in the tube to the strain energy U2in the solid bar if the maximum shear stresses are the same in both cases? (For the tube, use the approximate theory for thin-walled bars.)
Find expressions for shear force V and moment M at v = L/2 of beam AB in structure (a). Express V and M in terms of peak load intensity q0and beam length variable L. Repeat for structure (b) but find Fand M at m id-span of member BC.