The dimensions of the beam with the cross-section are given as b, a, t as in the figure on the right. The section is under the influence of the eccentric pressure force P. By constructing the equation of the neutral axis for this loading case Calculate the largest and smallest stresses that will occur in the section and show the normal stress distribution on the section. P kN=85 a (mm)=120 b (mm)=150 t (mm)=40

Q: The beam shown below has a cross section of channel shape with width b-400 mm and height h=80 mm,…

A: Answer: (a) The maximum tensile stress is 64.68 MPa. (b) The maximum compressive stress is 16.36…

Q: The cross-section of a concrete corner column that is loaded uniformly in compression is shown in…

A:

Q: Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected to loads…

A: This is a classic example of combined loading. The force 800N will create direct shear stress at…

Q: The screw of the clamp exerts a compressive force of 500 N on the wooden blocks. The cross section…

A: Given: The compressive force on wooden block, P = 500 N The cross-section of clamp at a-a, A = 3 cm…

Q: 1)The simply supported beam is subjected to loads as illustrated in the figure below. a) Draw shear…

A: As per company policy, we are restricted to solve only the first three sub-part of one question at a…

Q: 3) An overhanging wooden beam supports the loads as shown in the figure. The cross-sectional…

A: The free body diagram of the beam is given below, On taking moment about C, The force equilibrium…

Q: Loading situation of the bar with circular section geometry (radius R = 0.03 m) shown in the figure:…

A:

Q: The forces applied to the pulleys are given in the figure below. Accordingly, show the stress…

A: Given: The outer diameter of shaft, D = 25 mm The inner diameter of shaft, d = 20 mm

Q: 3 KN/m D B 120 mm YA= 40 mm A. 80 mm 1m 2 m 10 KN 10 KN L= 4 m

A:

Q: H.W: A steel pipe with an outside diameter of 4.500 in. and an inside diameter of 4.026 in. supports…

A:

Q: 7. A curved bar shown in the figure has a trapezoidal cross section. If it is subjected to a force…

A: The moment and force at section a-a is calculated as : V=-200+120=-80…

Q: 10 KN 20 KN / m 5 KN / m A B SIMPLE STRESSES 5 KN / m D 5 KN / m F 50 KN-m E 3. Points C and D of…

A: Given DataP=10kNw1=5kN/mw2=20kN/m

Q: 2) mid section t=4mm 3 45 ** 5cm 5um 5c

A: Data given: The force acting at the free end, P = 100 N The length of the cantilever beam, L= 1 m…

Q: A simple beam is loaded as shown in the figure below If the load P 120 kN determine the maximum…

A: Normal stress will be maximum at cross section 'B'Net normal stress = Normal stressaxial+Normal…

Q: Question 2)  arm of Figure  B  from point x z  plane, a horizontal angle of θ = 38 ° angled F = 29…

A:

Q: Rectangular cross-section and width given the loading state in the figure Bending safety stress of…

A:

Q: - : The forces as given below are applied as shown in the figure. F:=10 kN, F;=5 kN and F3=3 kN. The…

A: Given F1 = 10 kN F2 = 5 kN F3 = 3 kN To find Stress at point D Shear stress Principal stresses

Q: Find the normal stress value on the new x-axis obtained by turning 53° clockwise of the stressed…

A:

Q: The beam shown in the figure is made of Wood that has an Allowable Shear Stress of 200 psi;…

A:

Q: 20 KN / m 5 KN / m A B SIMPLE STRESSES 5 KN / m D 50 KN-m 5 KN / m F 2. Points C and D of the 1.00…

A: according to the given details

Q: A solid bar having a diameter 150 mm is to be replaced by a square tube having a cross-sectional…

A:

Q: 4 kN 3 kN 375 mm 375 mm B 750 mm As shown in the figure, the shaft is supported by bearings A and B…

A: Given data Material used A36  Diameter of the shaft = 50mm To determine the maximum theoretical…

Q: a) A simply supported beam with a rectangular cross section supports uniform load q. (see figure).…

A:

Q: Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected to loads…

A: Write down the given value using a suitable variable. Here d signifies rod diameter. Draw a free…

Q: The beam with its section, given in the figure; a) Calculate the value of the location of the…

A:

Q: In the figure, the steel shaft with a diameter of 36 mm is 240 mm diameter pulley. Belts also formed…

A:

Q: 1. A force of P: = 800 N is exerted on control arm BC, which is securely attached to the solid 30 mm…

A:

Q: In the figure, both ends of the rectangular plate are under the effect of a force p = 150kN. What is…

A:

Q: The above figure is a section of a column. If the said column is subjected to an axial load of FN x…

A:

Q: 40 N.m Da 0.5 m 280 N.m 150 N.m 2 0.3 m 0.4 m

A:

Q: The hollow shaft shown in the figure below is fixed at one end and has a lever at the other. The…

A:

Q: For the beam and loading shown in the figure below, determine: 1- The normal and shearing stresses…

A: Part 1 From fig we can say that the forces that play a vital role to form normal and shear stress…

Q: Find the normal and shear stresses at points H and K, since F= 15 kN in the loading condition shown…

A:

Q: D16. For the truss shown in figure determine the displacements at point B and stresses in the bars…

A: To determine the stresses in Part AB and BC.

Q: A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate…

A:

Q: Problem (4.7): For the thin-wall tubular sections shown in Figure (4.28); (a) Determine the maximum…

A:

Q: Consider the circular bent rod with diameter 20 mm. The free-end of the bend is subjected to loads…

A:

Q: arm of Figure  B  from point x z  plane, a horizontal angle of θ = 38 ° angled F = 29 kN force sized…

A: Given data, The angle θ=38° Applied Force, F = 29000 N  Applied moment, M = 17000 N-m Length of arm…

Q: The beam is acted upon by force F = 17 kN as shown in the figure.    What is the shear force in…

A:

Q: b) For purposes of analysis, a segment of the' crankshaft dimensions in a vehicle are represented as…

A:

Q: e member shown in Figure has a rectangular cross section. Determine the state of stress that the…

A: Consider the free body diagram: P=50*2.5 =125 KNtanθ=1.52θ=36.87°In Horizontal…

Q: A column with a wide-flange section has a flange width b = 200 mm , height h = 200 mm , web…

A:

Q: Two solid circular shafts (i.e., AB and BC) are fixed to rigid walls at point A and C, respectively.…

A:

Q: In the l-section fixed beam shown in the figure, the result of the loading situation; a) Find the…

A: Figure of I section is shown in figure,   B = Overall width of the section b= Thickness of the web…

Q: The figure below shows a simply supported prismatic beam with an applied uniform load.  The labeled…

A: let length of the beam is L All points are equally spaced therefore space between two points are L4…

Q: P to point A of the section given in the figure Plot the normal stress distribution in the section,…

A: Given dataP=20kN Here are calculation the Moment of inertia about the neutral axis

Q: 10 KN 20 KN / m 5 KN / m A SIMPLE STRESSES 5 KN / m 50 KN-m 5 KN / m 2. Points C and D of the 1.00…

A:

Q: a) Draw the bending moment diagrams My and Mz and torque T, determine the magnitude and location of…

A:

Q: Question 1) F=22 kN single load, M-24 kN.m moment and w=5 kN/m distributed load act on the beam…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.