The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 2.3 kN when 0 = 38°, determine the force P required on the lever and the corresponding tension T₂ for this position. Assume that the surface under A is perfectly smooth. Assume a = 100 mm, b = 590 mm. T₁ 4 B A Answers: P = i KN IN oooo Foxwo T₂ P

The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 2.3 kN when 0 = 38°, determine the force P required on the lever and the corresponding tension T₂ for this position. Assume that the surface under A is perfectly smooth. Assume a = 100 mm, b = 590 mm. T₁ 4 B A Answers: P = i KN IN oooo Foxwo T₂ P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The spring has a stiffness of 830 N/m and is undisturbed and measures 400 mm. Determine the forces on the BC and BD cables when the spring is stretched in the position shown in the figure.
If d=4ft, determine the force in cable AB, AC, and AD needed to support the 3500lb platform.
The collar C is fixed to rod AB using a glued bond that allows a maximum force of 405 N parallel to the axis of the rod. The collar has weight W acting in the negative z direction. Determine the weight W in N of the collar that will cause the glued bond to break as shown in figure.
How is 89.4 N obtained as the reaction at support C (See 2nd attached image) in this problem: Neglecting friction, determine the tension in cable ABD and the reaction at support C & the angle it makes w/ member AE.
The plate is made of steel having a density of 7850kg/m3. If the thickness of the plate is 10 mm,determine the horizontal and vertical components ofreaction at the pin A and the tension in cable BC.
Determine the tensions in the cable, normal force in the smoothsurfaces and the angle of inclination of the surface in the right ifthe block in the left and right weigh 300N and 500N,respectively. (Assume frictionless pulley)T =NA =NB =θB =
If a force of P=25N is applied to the handle of the mechanism, determine the force the screw exerts on the cork of the bottle. The screw is attached to the pin at A and passes through the collar that is attached to the bottle neck at B
The bracket is held to the wall using three A-36 steel bolts at B, C, and D. Each bolt has a diameter of 0.5 in. and an unstretched length of 2 in. If a force of 800 lb is placed on the bracket as shown, determine the force developed in each bolt. For the calculation, assume that the bolts carry no shear; rather, the vertical force of 800 lb is supported by the toe at A. Also, assume that the wall and bracket are rigid. A greatly exaggerated deformation of the bolts is shown.
Determine the tensions T1 and T2 in the strings required to maintain equilibrium for the suspended object weighs W = 38.7N shown in the figure. Take, α = 29.8° & β = 50.2°. The value of θ1 (Degree) = The value of θ2 (Degree) = The value of θ3 (Degree) =
The post is made of Douglas fir and has a diameter of 100 mm. If it is subjected to the load of 20 kN and the soil provides a frictional resistance that is distributed along its length and varies linearly from w = 4 kN>m at y = 0 to w = 12 kN>m at y = 2 m, determine the force F at its bottom needed for equilibrium. Also, what is the displacement of the top of the post A with respect to its bottom B? Neglect the weight of the post.
The metal strap has a thickness t and width w and is subjected to a temperature gradient T1 to T2 (T1 6 T2). This causes the modulus of elasticity for the material to vary linearly from E1 at the top to a smaller amount E2 at the bottom. As a result, for any vertical position y, measured from the top surface, E = [(E2 - E1)>w]y + E1. Determine the position d where the axial force P must be applied so that the bar stretches uniformly over its cross-section. w
determine the tension in all three cables if the bouyancy force on the balloon is 1035 N, the mass of the system is 87.7 kg, the balloon is held at a height of 12 m above the ground (A=(0,12,0)), and the student volunteers are located B = (15, 0, 18.9) m, C = (12.1, 0, -13) m, and D = (-17.6, 0, 3) m. Find tension in cables AB, AC, AD.