The clamp exerts a 145 lb compressive force on the wood blocks. Single-threaded screw BC has lead L = 0.190 in. and mean diameter d= 0.370 in. It turns in the threaded sleeve at C and pushes against B. The coefficient of staticfriction between the screw threads and the threaded sleeve is= 0.300. Neglect friction at B.2 in.2 in.2 in.B2.25 in.2.40 in.2.25 in.(a) Determine the value of the moment M in ft · Ib to increase the clamping force. (Enter the magnitude.)ft · Ib(b) Determine the value of the moment M in ft · Ib to decrease the clamping force. (Enter the magnitude.)ft · Ib

Answered: Image /qna-images/answer/e8b0022f-7cea-400e-9cb5-5f97d45a8cb8.jpg

The clamp exerts a 145 lb compressive force on the wood blocks. Single-threaded screw BC has lead L = 0.190 in. and mean diameter d = 0.370 in. It turns in the threaded sleeve at C and pushes against B. The coefficient of static friction between the screw threads and the threaded sleeve is u. - 0.300. Neglect friction at B. 2 in. 2 in. 2 in. A C • 2.25 in. 2.40 in. 2.25 in. (a) Determine the value of the moment M in ft · Ib to increase the clamping force. (Enter the magnitude.) ft· Ib (b) Determine the value of the moment M in ft · Ib to decrease the clamping force. (Enter the magnitude.) ft · Ib

The clamp exerts a 145 lb compressive force on the wood blocks. Single-threaded screw BC has lead L = 0.190 in. and mean diameter d = 0.370 in. It turns in the threaded sleeve at C and pushes against B. The coefficient of static friction between the screw threads and the threaded sleeve is u. - 0.300. Neglect friction at B. 2 in. 2 in. 2 in. A C • 2.25 in. 2.40 in. 2.25 in. (a) Determine the value of the moment M in ft · Ib to increase the clamping force. (Enter the magnitude.) ft· Ib (b) Determine the value of the moment M in ft · Ib to decrease the clamping force. (Enter the magnitude.) ft · Ib

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.72P

See similar textbooks

Similar questions

The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
Two loads P1 and P2 resting on two inclined plane and connected by a horizontal chord AB as shown in figure. If P2 = 1200 kN determine the maximum and minimum value of P1 and tension in chord AB so that the static equilibrium exist the angle of limiting friction is 23o at all rubbing surfaces.
The figure shows a bar in equilibrium position resting on the floor at point A and on the wall at point B. If the mass of the bar is m and the angle it makes with the floor is θ = π/6, find the magnitudes of the frictional and normal forces at points A and B.
....An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley is 2.89 rad and the belt speed runs at 29.36 m/s. The groove angle of the pulleys is 35°. Determine the tension in the slack side of the belt in N if the belt has a cross-sectional area of 366 mm2, density 1000 kg/m3, and an allowable tensile stress of 2.3 MPa. The coefficient of friction between the belt and the pulley is 0.3
Box A weighs 1000N and has a height of H1=3m and width W1=2m. Box B weighs 800N. the static friction coefficient between the boxes is uA=0.7 and the static friction coefficient between box B and the ramp is uB=0.5. Find the max allowable angle for the following instances where no motion occurs, box A and B remain stationary. 1) Box A slides, Box B remains stationary 2) Box A tips, Box B remains stationary 3) Box B slides, Box A remains stationary on block B
Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
Gate AB retains water as shown in the figure. The gate is supported every 2 m (perpendicular to the plane of view) by member BC, which is attached to a 2000 kg mass at point C. What minimum static coefficient of friction μs, along the contact surface between the mass and its base, is needed for the gatestructure to be in equilibrium? There are pins at pointsA, B, andC.
The box shown in the figure has a weight of 250 pounds.The coefficient of static friction between the box and the floor is 0.4.Determine the maximum force P that can be applied to the box, withoutlet this move.
A load of Ft = 700 N comes to the free wheel of a car. The coefficient of friction between road and tire is µT = 0.8. Wheel radius is twice the disc friction radius (Rt = 2 Rs), µ = 0.35 between pad and disc and allowable pressure p = 0.5 N/mm2 Determine the pad sizes and the hydraulic pressure that should be sent to the piston. Piston's diameter is d = 30 mm.
In the vise shown in the figure, the screw is single-threaded in the upper member; it passes through the lower member and is held by a frictionless washer. The pitch of the screw is 3 mm, its mean radius is 12 mm, and the coefficient of static friction is 0.15. Determine the magnitude P of the forces exerted by the jaws when M = 74-N·m couple is applied to the screw. The value of magnitude P is kN. Note: please show correct step by step working out!. And double check the final answer. Thanks.