The drawing shows a solid cylindrical rod made from a center cylinder of lead and an outer concentric jacket of copper. Except for its ends, the rod is insulated (not shown), so that the loss of heat from the curved surface is negligible. When a temperature difference is maintained between its ends, this rod conducts 1/5 the amount of heat that it would conduct if it were solid copper. Determine the ratio of the radii r₁/r2. Number i Units Copper Lead

The drawing shows a solid cylindrical rod made from a center cylinder of lead and an outer concentric jacket of copper. Except for its ends, the rod is insulated (not shown), so that the loss of heat from the curved surface is negligible. When a temperature difference is maintained between its ends, this rod conducts 1/5 the amount of heat that it would conduct if it were solid copper. Determine the ratio of the radii r₁/r2. Number i Units Copper Lead

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.35P

See similar textbooks

Similar questions

As a designer working for a major electric appliance manufacturer, you are required to estimate the amount of fiberglass insulation packing (k = 0.035 W/m K) that is needed for a kitchen oven shown in the figure below. The fiberglass layer is to be sandwiched between a 2-mm-thick aluminum cladding plate on the outside and a 5-mm-thick stainless steel plate on the inside that forms the core of the oven. The insulation thickness is such that the outside cladding temperature does not exceed 40C when the temperature at the inside surface of the oven is 300C. Also, the air temperature in the kitchen varies from 15Cto33C, and the average heat transfer coefficient between the outer surface of the oven and air is estimated to be 12.0W/m2K. Determine the thickness of the fiberglass insulation that is required for these conditions. What would be the outer surface temperature when the inside surface of the oven is at 475C?
A square steel alloy plate 400 mm on a side has a 90-mm-diameter circular hole at its center. The plate is heated from 20°C to 45°C. The final diameter of the hole is ____ mm.
Q4. Two long rods of the same diameter, one of brass(k= 85 W/mK) and the other of copper (k=375 W/mK) have one of their ends inserted in a furnace and the other ends exposed to the same atmosphere. At a distance of 105mm away from the furnace, the temperature of the brass rod is 120' C. Find the distance from the furnace in which the copper rod have the same temperature.
Derive the expression of q on a flat furnace wall in the x-direction
The compartment below is used as a freezer of refrigerator compartment. Inner wall is at -10 C and outer wall is at 20 C. Insulator with a thermal conductivity of 0.040 W/(mK) is used to prevent the heat losses from the compartment. The shape is in square form with a side of 1.3 m and unit width into the page. Determine the amount of the heat load if the thickness of the insulator is 2 cm? *
The shearing strain of a block of metal 3” high is subjected to a shearing force which distorts the top surface through a distance of 0.0036 inch.
In addition , the space between the upper cap, the lower cap, and the cylindrical wall is filled with linear insulating material of permeability u.
What will be the rise in temperature in 30 minutes of a block of copper of 500-gram mass if it is joined to a cylindrical copper rod 20 cm long and 3.0 mm in diameter when a temperature difference of 80 degree Celsius is maintained between ends of the rod? The thermal conductivity of copper is 1.02 cal/cm2-sec-°C/cm (neglect heat losses). Please include FBD
a metal bar is made up of 3.0 cm of aluminum and 5.0 cm of steel. the free end of the aluminum bar is placed in contact with steam at 100 degree Celsius. at the other side, the free end of the steel bar maintained at 0 degree Celsius by placing it in contact with the ice. find the temperature at the point that connect the aluminum and the steal (junction)
I want to know how much heat the tube lost due to the material it is made of aluminum or steel. Even if it is a small difference in temperature. I want to know which material Conduct Heat the Best through this problem. material: Aluminum, steel ( the dimensions are the same for both) temperature touching cylinder: 65 Celcius temeprature inside cylinder 64.5 celsius room temperature 24 celcius Tube measurements outer radius r1 r1 = 4 in inner radius r2 r2 = 3 in outer circumference C1 C1 = 25.132741228718 in inner circumference C2 C2 = 18.849555921539 in height h = 8 in wall thickness t = 1 in
Is the frame determinate or indeterminate? Support your answer.
3500J / s of energy is transferred from a heat source to the surface of the part. The heated region is circular and the heat density decreases as the radius increases. Find out whether the heat density is sufficient to melt the metal since 70% of the heat is concentrated in a circle with a diameter of 3.75 mm.