The effective value of Va, Vb, Vc in the given system is 220, Ly=350 mH and Ry=35 Ohm. It has been observed that the load current is continuous when the transistors are triggered for alpha=40 degrees. Average value of D1 diode current = 0.438 A. accordingly, what is the average current value of the current through T3? ABсDSoru 4MemRy LyOO1.902.241.755.70Verilen sistemde; Va,Vb, Vc etkin değeri 220V, Ly=350 mH ve Ry-35 Ohm'dur.Tristörler alfa-40 derece için tetiklendiğinde yük akımının sürekli olduğu gözlemlenmiş ve D1diyot akımının ortalama değeri ID1_ort=0.438A olarak hesaplanmıştır.Buna göre; T3 üzerinden akan akımının ortalama değerini hesaplayınız. IT3_ort=?

The above question is based on a 3-phase half-wave controlled rectifier with a freewheeling diode…

The effective value of Va, Vb, Vc in the given system is 220, Ly=350 mH and Ry=35 Ohm. It has been observed that the load current is continuous when the transistors are triggered for alpha=40 degrees. Average value of D1 diode current = 0.438 A. accordingly, what is the average current value of the current through T3?

The effective value of Va, Vb, Vc in the given system is 220, Ly=350 mH and Ry=35 Ohm. It has been observed that the load current is continuous when the transistors are triggered for alpha=40 degrees. Average value of D1 diode current = 0.438 A. accordingly, what is the average current value of the current through T3?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1P: Given the complex numbers A1=630 and A2=4+j5, (a) convert A1 to rectangular form: (b) convert A2 to...

See similar textbooks

Similar questions

Perform the following steps for the given circuit in below.RD = 1.8kΩ, RS = 560Ω, RG = 2.2MΩ, VDD = +9V, IDSS = 6mA, VP = -6Va) Calculate the ID current and VDS voltage of the JFET.b) Calculate the ID current and VDS voltage of the JFET, if the value of IDSS = 8mA,VP = -6V.c) Calculate the ID current and VDS voltage of the JFET, if the value of IDSS = 6mA,VP = -4V.d) Find the working region of the JFET for the all cases given above.
Soru 1) Yukarıda Y-bağlı dengeli üç fazlı jeneratöre Y bağlı dengeli üç fazlı bir yük bağlanmıştır. Jenratörün iç direnci Zs =0.4+j0.3 ohm, hat direnci Zl=0.6+j0.7 ohm ve dengeli üç fazlı her birin yükün değeri ZL=9+j58 ohm'dur. Üç fazlı kaynak positive sıraya dizilmiştir ve genliği |Van|=222 ve faz açısı 30 derece ise (a) Vbc hat geriliminin genliği , (b) Ic hat akımının genliğini ve (c) 3 fazlı yükteki kompleks gücü bulunuz. Q.1) A Y-connected balanced three-phase generator with an impedance of Zs =0.4+j0.3 ohm per phase is connected to a Y-connected balanced load with an impedance of ZL=9+j58 ohm per phase. The line joining the generator and the load has an impedance of Zl=0.6+j0.7 ohm per phase. Assuming a positive sequence for the source voltages and that amplitude of |Van|=222 and its phase angle 30 degree Find: (a) amplitude of the line voltage Vbc, (b) amplitude of the line current Ic, (c) the complex power at the balanced three-phase load. a. (a) Vb=384,52 V, (b)…
Three generators are rated as follows: G1: 100MVA, 33kV, xg1 = 0.1pu G2: 150MVA, 32kV, xg2 = 0.08pu G3: 110MVA, 30kV, xg3 = 0.12pu. Determine the reactance of the generator corresponding to base values of 200MVA and 35kV
Variation of which of the following parameter is not consider as power quality problem for industry?VoltageCurrentPowerFrequency
Suggested answers: a)hie1= 2.624kohms hie2= 2.624kohms b) ads= 95.27 add= 190.541 c) Acs= 0.3294 acd= 0
Wm(t)/ea(t)= 1838.41/(p+155.1)
urgjhguyguhiu
Underg.cables.EE.
make me an example of a complex power pls. asap
4. An inductive reactance , XL= j 12 ohms, A resistance of R= 10 ohms and capacitive reactance of Xc= -j15 ohms are connected in parallel across a120 volts 60 hertz supply. Find the total current
determine the following by DC Analysis. a. IDQ b. VGse c. VDS RD=4 KOhms VGG=2volt
Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?v