2. The circuit shown in the below Figure utilizes an ideal op amp. 10 kN Vx RL 11100 0 10 kN a) Calculate currents I1, I2, I3, IL and the voltage Vx. b) Calculate the maximum RL, if the minimum value of Vo is -13 V. c) If RL is changed in the range between 1002-1 k2, what is the corresponding variation in IL and in Vo?

2. The circuit shown in the below Figure utilizes an ideal op amp. 10 kN Vx RL 11100 0 10 kN a) Calculate currents I1, I2, I3, IL and the voltage Vx. b) Calculate the maximum RL, if the minimum value of Vo is -13 V. c) If RL is changed in the range between 1002-1 k2, what is the corresponding variation in IL and in Vo?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

The op amp as shown is used to increase the overall output resistance of current source M1. If VREF = 5V, VDD = 0 V, VSS = 15 V, R = 50 kΩ, Kn = 800 μA/V2, VT N = 0.8 V, λ = 0.02 V−1, and A = 50,000, what are the output current Io and output resistance of the current source?
For the circuit, assuming an ideal op amp, and given Vs = - 1.5 V, R1 = 1 K ohm, R2 = 15k ohm, and R3 = 5k ohm, answer the following question. (Annotate diagram to show branches and nodes.) (a) Find the currents in all the branches (b) Find the voltages at all nodes (c) Find the power dissipated in each resistor (a) Find the total power dissipated in all resistors (e) How much power is delivered by Vs? (f) Explain: where does the rest of the power come from?
The following Operational Amplifier circuit is given. Analyze the circuit carefully to identify the functions (i.e., OP-AMP configurations) of each OP-Amps. Calculate the first stage output voltage Vx and then the output voltage at the output of the second stage Vo . Determine the currents I0, IF, and IX . Finally, determine the power absorbed by the resistor R7. The resistors: R2 = R4 =100 kiliohm. R1 = R3 = 10 kiliohm, R5 = 10 kiliohm, R6 = 90 kiliohm. and R5 = 10 kiliohm. The load resistor R7 = 10 kiliohm. The current source; I1 = 100μA and V2 = 1V.
Specify RfRf, given that vi = 19 V *The resistor Rf in the circuit in the figure is adjusted until the ideal op amp saturates.*
The op amp as shown is used in an attempt to increase the overall output resistance of the current source circuit. If VREF = 5 V, VCC = 0 V, VEE = 15 V, R = 50 kΩ, βo = 120, VA = 70 V, and A = 50,000, what are the output current Io and output resistance of the current source? Did the op amp help increase the output resistance? Explain why or why not.
The circuit utilizes an ideal op amp 1)Find I1, I2, I3, IL and Vx. 2) If VO is not to be lower than -6V, find the maximum allowed value for RL. 3) If RL is varied in the range 200Ω to 600Ω, what is the corresponding change in IL and VO?
The op amp in the circuit shown is ideal. 1. Calculate vo if va=1 V and vb=0 V. 2. Repeat (a) for va=1 V and vb=2 V. 3. If va=1.5 V, specify the range of vb that avoids amplifier saturation.
The op amp in the noninverting amplifier circuit shown has an input resistance of 400 kΩ, an output resistance of 5 kΩ, and an open-loop gain of 20,000. Assume that the op amp is operating in its linear region. 1. Calculate the voltage gain (vo/vg). 2. Find the inverting and noninverting input voltages vn and vp (in millivolts) if vg=1 V. 3. Calculate the difference (vp-vn) in microvolts when vg=1 V. 4. Find the current drain in picoamperes on the signal source vg when vg=1 V. 5. Repeat (a)–(d) assuming an ideal op amp.
The following Operational Amplifier circuit is given. Analyze the circuit carefully to identify the functions (i.e., OP-AMP configurations) of each OP-Amps. Calculate the first stage output voltage Vx and then the output voltage at the output of the second stage Vo . Determine the currents I0, IF, and IX . Finally, determine the power absorbed by the resistor R7. The resistors: R2 = R4 =100KW. R1 = R3 = 10W, R5 = 10W, R6 = 90 KW. and R5 = 10W. The load resistor R7 = 10KW. The current source; I1 = 100μA and V2 = 1V.
The op amps as shown are ideal (a) What are the voltage gain, input resistance, and output resistance of the overall amplifier? (b) If the inputvoltage υI = 1 mV, what are the voltages at each of the eight nodes in the amplifier circuit?
If they are defined as R1=12Ω, R2=5Ω and VS=5V respectively in the circuit given below, how many amps is the İ1 ambient current value? Help me please... Thank you so much.
Assume all op amps are ideal.1) What is the name of the op amp circuits in the dashed box?2) Explain briefly what is the purpose of having the op amp circuits in thedashed box.3) What are the input resistances seen by VA, and by VB?4) What is the output resistance?5) What is Vo in terms of VA and VB, assuming all resistors in this circuit havethe same resistance?