The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 x 2- C, grade 5.8, with rolled threads as shown in the figure below, on which an external load P = 10.9 KIN/bolt is applied. Km =5.2kp. Steel bolt k = k/a End plate Cylinder Calculate external load, Ph acting on the permaent connection bolts in kN units. Enter only numeric value without units.

The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 x 2- C, grade 5.8, with rolled threads as shown in the figure below, on which an external load P = 10.9 KIN/bolt is applied. Km =5.2kp. Steel bolt k = k/a End plate Cylinder Calculate external load, Ph acting on the permaent connection bolts in kN units. Enter only numeric value without units.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.10P: Three round, copper alloy bars having the same length L but different shapes are shown, in the...

See similar textbooks

Similar questions

Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal arm AB (length b = 10 in.) and a vertical arm BC (length c = 7 in.) pivoted al point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer al C is controlled by a spring, Jt = 5 lb/in., that is attached to a threaded rod. The pitch of the threads is p = 1/16 in. Under application of load W, 12 revolutions of the nut are required to bring the pointer back to the mark. Calculate the weight W.
A cable and pulley system at D is used to bring a 230-lcg pole (ACB) to a vertical position, as shown in the Figure part a. The cable has tensile force T and is attached at C. The length L of the pole is 6.0m, the outer diameter is d = 140 mm. and the wall thickness is t = 12 mm. The pole pivots about a pin at A in figure part b. The allowable shear stress in the pin is 60 MPa and the allowable bearing stress is 90 MPa. Find the minimum diameter of the pin at A in order to support the weight of the pole in the position shown in the figure part a.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in. passes through each davit and supports two pulleys. are on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a =15° with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that can be carried in the lifeboat?
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Example 8-4 in SI Units. • Q-2 Figure gives the cross section of a grade 25 cast-iron pressure vessel. A total of N bolts are to be used to resist a M16 x 2 x 60 mm class 5.8 separating force of 36 kip (160.2 kN). • (a) Determine k,, Kmy and C. • (b) Find the number of bolts required for a load factor of 2 where the bolts may be reused when the joint is taken apart. hexagonal head bolt No: 25 CI 20 mm 20 mm • (c) With the number of bolts obtained in part (b), determine the realized load factor for overload, the yielding factor of safety, and the load factor for joint separation. H = 14.8 mm
The figure gives the cross-section of a grade 25 cast-iron pressure vessel. A total of N bolts are to be used to resist a separating force of 150 kN. (a) Determine kb, km, and C. (b) Find the number of bolts required for a load factor of 2 where the bolts may be reused when the joint is taken apart. (c) With the number of bolts obtained in part (b), determine the realized load factor for overload, the yielding factor of safety, and the load factor for joint separation. Use (SI) units as it applies
Two plates are clamped by a 3/4-10 UNC SAE Grade 5 bolt and regular nut with a 3/4-W plain washer as shown in figure. Top plate is made of grey cast iron and bottom plate is steel. An axial force of 12kN is acted upon the joint. Round off the length of the bolt to nearest 1/4in. Assume bolts are preloaded to 75% of proof load. 1. Determine the bolt stiffness kb. 2. Determine the member stiffness km. 3. Determine the yielding factor of safety of the bolt. 4. Determine the load factor for the bolt. 5. Determine the load factor guarding against joint separation. 1.25 in 1.00 in
5. A butt connection is shown in the following figure. Plates is Q235 steel; 8.8 Grade M16 high- strength bolts; The diameter of holes is 18mm; pretension P-80KN, µ=0.45; a = e = 50mm, b=2×60mm; g= 2×80mm , c = 110mm, ti = 8mm, t2 = 20mm. Steel yield stress f=205 N/mm?; Effective bolt area Ac=157 mm²; f.=470N/mm2;f-250N/ mm?. (1) Assume slip-critical connection, calculate the load-bearing capacity N. (2) Assume bearing type connection, calculate the load-bearing capacity N. + + || +
The section of sealed joint shown in figure below is loaded by a force cycling between 2 and 6 kips. The member have E = 30 Mpsi. The bolts have been preloaded to F; =35 kip each. ž in-16 UNF x 24 in SAE grade 5 No. 40 CI (a) Find the fatigue factor of safety using Goodman criterion for above loading. (b) Find the fatigue factor of safety using Goodman criterion if force cycling between 0 and 6 kips.
Data: r=0.25 inch, d=0.4 pig and h=0.5 inch, wi=2.5 inch and w= 1.5 inch.The forces fluctuate between a tension of 14 Kips and a compression of 5 Kips. It is made of AISI 1018 CD. steel.The connecting element in the figure is failing. What is the most critical point and give recommendations to improve the situation.