Answered: The flow energy of 24 li/min of a fluid…

The flow energy of 24 li/min of a fluid passing a boundary to a system is 2 kJ/sec. What is the pressure at this point? а. 100 kPa b. 140.39 psi c. 1, 000 kPa d. 871 kPa

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.4P: 5.4 Evaluate the Stanton number for flow over a tube from the following data: , , , , .

See similar textbooks

Related questions

Q: A fluid moves in a steady flow manner between two sections in a flow line. At section 1: A_1 =2…

Q: The flow rate of air moving through a square 0.50-m by 0.50-m duct is 160 m3/min. What is the mean…

Q: Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of…

Q: The fan/blower installed in the central air conditioning system is of the axial flow type. This…

A: Given: Po = 110.29 kPa Patm = 101.3 kPa V = ?

Q: Water (20°C, saturated) enters a 2 in. Sch. 40 pipe at a velocity of 1.0 m/s and a pressure of 1…

A: A pipe is given at some elevation to the ground and using Bernoulli's theorem we can solve this…

Q: 18. Water flows steadily through the pipe system These data apply: D1 = 1 ft, D2 = 0.5 ft; p1=12…

Q: Water at 60°F is pumped from a reservoir to the top of a mountain through a 6-in. Schedule 120 pipe…

Q: Hydro-machinery such as turbines and pumps represent fluid devices that have wide variety of…

Q: 7.) The pressure drop associated with hydraulic fluid with a Sg of 0.93 flowing across a 1-in. I.D.…

Q: A wind tunnel has an inlet section with a velocity of 360 ft/s at standard atmospheric conditions.…

Q: Example 1.14 Calculate the pipe bores required for the suction and pressure lines of a pump…

A: Given data: The discharge through pipe is Q=40 Lmin=0.67×10-3 m3s The maximum velocity in suction…

Q: Provide one question and its solution involving an external flow of fluid .

Q: A fluid jet discharging trom a 100 mm diameter orifice has a diameter of 80 mm at its vena…

A: Given Jet diameter, D = 100 mm Orifice diameter, d = 80 mm Find The coefficient of…

Q: 20-/ In figure shown if head loss was ignored between A and B, the flow rate=0.05 m3/sec. find the…

A: Given, Flow rate, Q=0.05m3/sPA=55KPadA=30cm=0.3mdB=20cm=0.2mZA=10mZB=6m We know…

Q: A pump is to deliver 80 galloons/min of water 60°C with discharge pressure of 1000 kPag. Suction…

Q: onical flow meter d of 0.3 kg/s, as show

Q: Guava juice enters a pipe with an ID of 3.05 inches at a rate of 15.6 ft3 / hr, then exits through a…

Q: The initial condition of air in an air compressor is 99 kPa and 30 deg. C and discharges at 438 kPa.…

Q: A steady push on the piston in Fig. causes a flow rateQ = 0.15 cm3/s through the needle. The fluid…

A: Given Data: The flow rate is Q = 0.15 cm3/s. Density of fluid ρ = 900 kg/m3. Dynamic viscosity is μ…

Q: Ex 4: For a flow rate Of 2 m/s Of air (pg 12 N/m') what is the largest A2 that will cause water to…

Q: The inlet of a centrifugal pump is 7 ft above a water surface level. The reentrant inlet (KIN = 1)…

A: when V is flow velocity through pipe head required by pump is equal to head loss ue to friction and…

Q: The velocity of a liquid (s.g.=1.96) in a 13-in pipeline is 1.2 ft/s. Calculate the flow in slug/s.

A: Specific gravity of the liquid, SG= 1.96 Diameter of the pipe, D= 13 in= 13(0.0254) m= 0.3302 m…

Q: A rotameter has a stainless steel float [ ρ=8500 kg/m^3] and takes in 5 m3 /min of water. Using…

A: Density of float, ρfloat=8500 kg/m3Volume flow rate of water, Qw=5 m3/minDensity of the given fluid,…

Q: Would the smallest, or the largest, of the seven Taco, Inc.pumps in Fig. be better (a) for…

A: First try the smallest pump, D = 10.00 in. Read Fig.: Q* = 390 gal/min, H* = 41 ft, ηmax = 65%.…

Q: Water is to be supplied to the inhabitants of a college hoste through a supply main. The following…

A: Given:L=4000 mn=3000Water consumed per day, q=180 Lhl=18 mf=0.007t=8 hrs

Q: A pump discharges into a 3-m per side cubical tank. The flow rate is 300 liters per minute and the…

Q: 2). Calculate friction heads when a flow rate of 1.5 m³/min circulate in two different pipelines.…

A: Given: The flow rate of water solution, Q = 1.5 m3/min The diameter of pipes, D2 = D1 = d = 2 in The…

Q: Water (20°C, saturated) enters a 2 in. Sch. 40 pipe at a velocity of 1.0 m/s and a pressure of 1…

Q: Suppose that you are willing to determine the diameter of the water jet impinging to the sink from…

Q: A and B are homologous pumps operating at the speed of 800rpm.Pump A has an impeller with diameter…

Q: In a wastewater treatment plant, Blower supplies air to the sequencing batch reactor. It is…

A: Write the given data. Cpitot=0.98ρair=1.2 kg/m3ρwater=1000 kg/m3hwater=75 mm

Q: 1) Discuss the difference in the velocities of the model and main pipe.

A: Given that,

Q: A fan is listed having the following performance with standard air: Volume discharge : 120m3 /s…

Q: Two pumps (Pump A and B) have performance curves which can be approximated by the following…

A: Head Discharge If two pumps are in series Head is not constant Discharge is constant If two…

Q: Oil at 155°F and 2250 psi is flowing through a pressure relief valve at 25 gpm. What is the…

A: Given Oil temperature = 155 F Pressure = 2250 psi Relief valve = 25 gpm To find Temperature of oil…

Q: is d, where it is d, for the delivery one. The pump receives a mechanical power P from an electric…

Q: Water at 21 C flows downward in a pipe a

A: detailed answer given below.

Q: A venturi meter similar to the one shown below has an inlet diameter of 100 mm and a throat diameter…

Q: A 10-in. x 6-in. x 12-in. duplex direct-acting steam pump operating at 35 strokes per minute…

A: Given: T=150°C slip=7% Stokes per min = 35

Q: fire -5 m² Figure shows a portion of a protection system in which a pump draws water at 60°F (v…

A: Given data: Q=1500 gal/min=3.34 ft3/sd=10 in Need to determine the required height "h" of the water…

Q: he speed of water in a pipe of about 3 meters in diameter can be measured by a. pitot tube b.…

A: the pitot tube is basically used to ensure the velocity of the fluid at any instant with respect to…

Q: A pumping system has the following characteristics, f=0.015 length of the pipe = (2500 ft) pipe…

A: Friction factor, f=0.015Pipe length, L=2500 ftPipe diameter, d=6 in=612ft=0.5 ftLosses less than…

Q: Water (density 62.4 lb/ft3, viscosity = 1 cP) is pumped from a large reservoir on the floor at a…

Q: Assume that 57 L/s of oil SG = 0.86 is pumped through a 300 mm diameter pipeline of cast iron. If…

A: Volumetric flow rate of oil, Q=57 L/s=0.057 m3/sSpecific gravity of oil, SGo=0.86Diameter of pipe,…

Q: Q/ A Newtonian fluid with adensity of (910) Kg/m3, flows through a (25) mm diameter Pipe with…

Q: centrifugal pump installation has been designed to discharge 0.126 m^3/s of brine (sp.gr. = 1.2).…

Q: The flow rate of a hydraulic fluid with a Sg of 1.08 through a 2-in. I.D. orifice is 50 gal/ min. If…

Q: A centrifugal pump has a suction pipe with a diameter of 100 mm, and a delivery pipe with a…

Q: How tall would the jet of water be from the top of the nozzle? PR 16.5 kPa Jet 1.8 m 0.2 m 0.2 m…

Question

The flow energy of 24 li/min of a fluid passing a boundary to a
system is 2 kJ/sec. What is the pressure at this point?
а. 100 kPa
b. 140.39 psi
c. 1, 000 kPa
d. 871 kPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

urgent need in 5 mins pls :( 8 g/cm3 of air flowing in a speed of 12 m/hr and with an area of 9 cm2. Calculate mass flow rate of air in second rate.
Chlorine gas enters a 30-mm ID pipe at 15 m/s, and exits a wider pipe, at 85-mm ID. What is the average velocity through the exit pipe (in m/s)?
An orifice on vertical wall has a head of 1.13m of oil ( sp.gr.=0.89). It discharges 6192N of oil in 88 seconds . The trajectory measures yield x = 2.4m and y = 1.37m . Assuming the area of the opening is 25cm2, Calculate Coefficient of Contraction, Coefficient or Velocity
A 0.5-inch diameter water pipe is 18 m long and delivers 19 L/min. What fraction of this pipe is taken by the entrance region?[Ans. LE /L=1.7%]
Engine oil at 40 deg.C, density is 875 kg/m3 flow into a 25.4 mm horizontal pipe with a velocity of 3.3 fps and exits through a nozzle of 0.20 in diameter. If the pressure drop is 78 psi, what must be the exit velocity in m/s? Show the unit cancellation.
Air velocity in a duct is measured as 38.2 m/s by a pitot tube. Density of flowing air 1.3 kg/m3. If the pressure difference recorded by the pitot static tube is 0.1 m of water, calculate the coefficient of velocity of the pitot static tube. A Figure or Free Body Diagram will be much appreciated. Thank you
5. The total head of a fan is 185 m and has a static efficiency pressure of 210 mm of water gage.What is the velocity of air flowing if the density of air is 1.15 kg per cubic meter? 8. A coal fired steam boiler uses 3000 kg of coal per hour. Air required for combustion is 15.5 kg ofcoal at barometric pressure of 98.2 KPa. The flue gas has temperature of 285 degree Celsiusand an average molecular weight of 30. Assuming an ash loss of 11% and allowable gas velocityof 7.5 meters per second. Find the diameter of the chimney 9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of…
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
Provide one question and its solution involving an external flow of fluid .
7.) The pressure drop associated with hydraulic fluid with a Sg of 0.93 flowing across a 1-in. I.D. sharp edge orifice is 20 lbf/in2 . If the discharge coefficient is 0.60, what flow rate in gal/min could be expected through the orifice?
A fan draws air at rest and propels it 45 meters through a rectangular duct measuring 200 by 300 mm. At a rate of 0.6m3/s, air enters at 15°C and 750 mm Hg absolute pressure. What is the required theoretical power?
Flow turbulence and cavitation in a centrifugal pump generate a similar sound to the human ear. Explain how vibration analysis would help you to determine which is which.