The flowrate between tank A and tank B shown in the figure below is to be increased by 20% (i.e., from Q to 1.20Q) by the addition of second pipe (indicated by the dotted lines) running from node C to tank B. If the elevation of the free surface in tank A is 15 ft above that in tank B, determine the diameter, D, of this new pipe. Neglect minor losses and assume that the friction factor for each pipe is 0.02. 6-in. diameter; 600 ft long 6-in. diameter: 500 ft long Diameter D, 500 ft long D= ft

The flowrate between tank A and tank B shown in the figure below is to be increased by 20% (i.e., from Q to 1.20Q) by the addition of second pipe (indicated by the dotted lines) running from node C to tank B. If the elevation of the free surface in tank A is 15 ft above that in tank B, determine the diameter, D, of this new pipe. Neglect minor losses and assume that the friction factor for each pipe is 0.02. 6-in. diameter; 600 ft long 6-in. diameter: 500 ft long Diameter D, 500 ft long D= ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

From the attached figure, determine the flow rate in each pipe taking into account that minor losses are negligible.
Water flows through the galvanized iron pipe system whose diameter is 0.75 inches and flow rate is 0.020 cfs. Do you agree with the fact that friction losses in the straight parts of the piping system are negligible with respect to losses to fittings?
3. What is the volumetric flow rate between two plates if the top plate is pulled, while keeping the bottom plate stationary, and simultaneously imposing pressure p0 on the left endof the channel, and pressure p0 + ∆p (∆p > 0) on the right end of thechannel.
The water flows through a taper pipe of length 100m having diameters 0.6m at the upper end and 0.3m at the lower end at the rate of 0.05m3 /s. If the pressure at the higher level is 196.2 kPa and the pipe has a slope of 1 in 40, then determine the pressure in the lower end.
Determine the discharge through three new cast-iron pipe connected in series, having diameters of 250mm, 200mm, 150mm and lengths of 600m, 360m and 270m respectively, When the total friction loss not including the minor losses is 5.0 m. Assume f=0.024 for all pipes.( hint: apply H= f.L.V²/( D.2.g)₁ + f.L.V²/( D.2.g)₂ + f.L.V²/( D.2.g)₃ and Q1=Q2=Q3 where Q=A.V ).
O1: A stream of water of diameter d = 0.1 m flows steadily from a tank of diameter D= 1.0 m. Determine The Weight Flowrate, needed from the inflow pipe if the water depth remains constant, 0 — d=010m
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. (DO NOT ROUND OFF)
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
Water from an open tank elevated 5m above ground is allowed to flow down to a pump. From the pump, it then flows horizontally through 100m of piping, and out into the atmosphere. If there are 2 standard elbows and one wide open gate valve in the discharge line, determine a) all friction losses in the system and b) the power requirement of the pump if it is to maintain 0.8 cubic meters per minute of flow. Assume a pump efficiency of 55%, and that friction is negligible in the pump suction line.
A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a pressure of 150 kPa. The throat diameter of the me- ter is 100 mm and the pressure at the throat is 400 mm of mercury below atmosphere. If 3% of the differential pressure is lost between inlet and the throat, determine the flow rate of the pipeline. PLEASE USE BERNOULLI'S ENERGY EQUATION. INCLUDE COMPLETE SOLUTION
A 15-ft-diameter tank discharges water at 50 F through a 2-in.-diameter sharp edged orifice. If the initial water depth in the tank is 10 ft and the tank is continuously pressurized to 50 psi, how long will it take to empty the tank?
Water at 20°C is withdrawn from a reservoir by means of a siphon, as shown in the figure. For d=10cm and D= 16cm, Determine: a) the minimum flow rate that can be achieved without cavitation occurring in the piping system, and b) the maximum elevation of the highest point in the piping system to prevent cavitation. c) Also, comment on the ways to increase the maximum elevation of the highest point in the piping system to prevent cavitation. (The saturation pressure of water at 20°C is 2.33 kPa)