I need the answer as soon as possible Water flows from section 1 to the reservoir at section 3 (where V3 = 0 ft/s) through first 300-ft long 2-in-diameter cast iron pipe then 100-ft long 3-in-diameter drawn tubing (the two sections are connected through asudden expansion) at a rate of 40 gal/min. Determine the pump power in hp at section 1.Z3 = 150 ftFlanged regular90° elbowSuddenSharp edged exitexpansionPI = ?Threaded regular90° elbowZ = 0 ftFully openglobe valve

Given DataL1=300ft=91.44md1=2in=0.0508mL2=100ft=30.48md2=3in=0.0762mQ=40gal/min=0.0252m3/sTotal…

Answered: Water flows from section 1 to the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

O1: A stream of water of diameter d = 0.1 m flows steadily from a tank of diameter D= 1.0 m. Determine The Weight Flowrate, needed from the inflow pipe if the water depth remains constant, 0 — d=010m
Calculate the total head of the system below. Assume a flow of 70 m³/h and that the pressure drops in the suction and discharge are 3 m and 4 m, respectively. ZA = 15m, ZB = 5m and ZC = 5m.
Reservoir A (Elevation 300m) supplies water to reservoir B (Elevation 180m) thru a 450 mm ductile iron pipe. A turbine is installed in the same level with Reservoir B. The total system flow is 350 gpm determine the the output power in Hp if the turbine is 75% efficient and the total headloss of the system is 3.5m.
The horizontal tube supplies 280 liters per second of water to a hydraulic turbine. The net head is 46.5 m determine the power supplies to the turbine
Water from an open tank elevated 5m above ground is allowed to flow down to a pump. From the pump, it then flows horizontally through 100m of piping, and out into the atmosphere. If there are 2 standard elbows and one wide open gate valve in the discharge line, determine a) all friction losses in the system and b) the power requirement of the pump if it is to maintain 0.8 cubic meters per minute of flow. Assume a pump efficiency of 55%, and that friction is negligible in the pump suction line.
Water at 10°C flows from a large reservoir to a smaller one through a 5-cm-diameter cast iron piping system, as shown in Fig. Determine the elevation z1 for a flow rate of 6 L/s.
Reservoir A (Elev. 106 m.) to the turbine is connected by a 638 mm pipe. Another 638 mm pipe connects the turbine to Reservoir B (Elev. 85 m.). The loss of head from A to 1 is 5 times the velocity head of the pipe and the loss of head from 2 to B is 0.2 times the velocity head of the pipe. If water is being discharged at a rate of 741 L/s, determine the horsepower required for the turbine to operate. (Assume 100% efficiency.)
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450 mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively. If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
Calculate the power required for a water pump used in a closed system with flow rate Q = 0.0076m ^ 3 / s . Assume that section area=0.00511 m² and at the area at the discharge is 0.0037m ^ 2
3. What is the volumetric flow rate between two plates if the top plate is pulled, while keeping the bottom plate stationary, and simultaneously imposing pressure p0 on the left endof the channel, and pressure p0 + ∆p (∆p > 0) on the right end of thechannel.
The turbine extracts 0 hp from the water flowing through it. The pipe with diameter of 1 ft and length of 300 ft is assumed to have a friction factor of 0 02. Minor losses are negligible. Determine flowrate through the pipe and turbine? Head losses is ?? = ?5 ft
A pump is required to pump water from a large reservoir to the water tower located 20 m above thereservoir (Figure 1). If 0.03 m3/s of water having a density of 1000 kg/m3is pumped through a 30-mmpipe.a. How much power is required to be delivered to the water by the pump? Consider the flow lossesin the pipe; do the necessary assumptions. b. Determine the efficiency of the pump

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS