The one line diagram of the system and data:Gl and G2:reactance=0.2 p.u ,11kv, 100MVAT1 and T2: reactance =0.05p.u, 11/132 kvLI: reactance=0.216p.u, 132kvL2=0.09p.u, 132kvL3=0.09p.u, 132kvCalculate the fault current when a three phase fault accurs at bus 55L2L3toL1

Fault Analysis- Transmission lines are represented using series reactance. So, the series resistance…

The one line diagram of the system and data: Gl and G2:reactance-D0.2 p.u,11kv, 100MVA T1 and T2: reactance =0.05p.u, 11/132 kv L1: reactance=0.216p.u, 132kv L2=0.09p.u, 132kv L3=0.09p.u, 132kv Calculate the fault current when a three phase fault accurs at bus 5 L3 3 T2 T1 to G2 L1

The one line diagram of the system and data: Gl and G2:reactance-D0.2 p.u,11kv, 100MVA T1 and T2: reactance =0.05p.u, 11/132 kv L1: reactance=0.216p.u, 132kv L2=0.09p.u, 132kv L3=0.09p.u, 132kv Calculate the fault current when a three phase fault accurs at bus 5 L3 3 T2 T1 to G2 L1

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.23MCQ: Does an open- operation, the kVA rating compared to that of the original thr-phase bank is (a) 2/3...

See similar textbooks

Related questions

Q: VI.For the figure below, if Z1 = 12 + j9 , Z2 = 18 – j7.5 Q and Vr = 23020° V, determine: (a) l1,…

A: In this question we will find power and power factor and current... Note:- as per our guidelines , I…

Q: Determine the loop currents values for the circuit. where R1= 170 (ohms), R2= 340 (ohms), R3= 85…

A: To find the loop currents I1 and I2 .

Q: Ean = 12020° v; Epn = 1202 – 120° v; Een = 1204120° v (grounded neutral) Zan = Zbn = Zen = 0.1 +…

A: Given information,

Q: Let I, = 95230°A, V, = 100Z – 20°V, Z1 = 20+ j602, R2 = 30N, R3 = 902, X2 = -90N, N1 = 3, and N2 =…

A: Here, we have given a step down transfer in th problem having the turns ratio 3:1. The values of the…

Q: In the network given in figure use nodal analysis to determine (a) the voltage at nodes 1 and 2, (b)…

A: In this question, We need to determine the voltage across the nodes as shown the circuit using the…

Q: A substation rated 1250 kVA is operating at full-load at 0.8 pf lagging and to carry an addition…

A: A substation is a place included in the electrical power generation system where electrical voltage…

Q: Q1. The circuit of Figure 1 has a source of 240V and source, line and load impedances according to…

Q: 17 In the figure shown, the voltage V1 the voltage V2 by. ||||||| out of phase. *

A: The Voltage waveform when represented on a same plot can be compared easily because they become…

Q: A power generation plant connected to bulk load of high voltage industries shown in Figure Q3 has…

Q: A residential four-wire system supplies power at 220 V rms to the following single-phase appliances:…

A: It is given in first phase there are 10 bulbs are connected each of power 60 W. Therefore, total…

Q: 200µ F Q.28: A complex voltage vr=30+50sin1000t-40sin2000t Volt, is applied across the circuit shown…

Q: Two power system areas operating at a nominal frequency of 60 Hz are connected with a tie line, and…

Q: For the mutual electric circuit shown in figure beside, find the set values of mesh currents 11 &12?…

A: According to question: The figure is drawn as The mutual inductive reactance between coils 1 &…

Q: I) If switch S is closed, what would be the ammeter and voltmeter reading? 2) Draw the phasor…

Q: 44) When doing delta-to-wye conversions A) if the resistances are equal in one configuration, then…

A: From the delta star conversion formulas decide which statement is correct.

Q: As shown in Figure Q1(b), two loads A and B are connected in parallel across a 1.5 kV r 60-Hz line.…

A: The solution can be achieved as follows.

Q: Assume you are an engineer in charge of a project and one of yoursubordinate engineers reports that…

A: Apply KCL on node of given circuit to check it satisfied or not Figure 1…

Q: 16 Three generators (Gl=G2=G3 = 150 MW) having samne Identical fuel cost characteristic. The to…

A: To find out the correct answer

Q: Is=10 A cosps=0.6 14=3 A cospa=0.8 45m F E 30m 15m TR 1 G D A 45m 45m U=20/0.38 kV I3=6 A V 15m…

Q: An inductive reactance of 10 ohms is connected in parallel with the capacitive reactance of 30 ohms.…

A: The impedances offered by a resistor, capacitor, and inductor are R, jXL and -jXC. Where, XL and XC…

Q: For the network shown in figure below, calculate the values of the following: Zi1, Z12, Zo1, Z02,…

Q: IDSS=8mA , VP =-4V To help plot the DC load line VGS=VG-IDRS a)Determine the value of Vgs when…

A: As per the guidelines of bartleyby I need to answer first three subparts only. So kindly repost…

Q: A Single Area consists of 3 generating units (G1/G2/G3) with the following characteristics: G1: 425…

Q: Using the nodal roint method in the sircuit shown in the figure, calculate the curxents passing…

Q: washing machine is, in effect, an RL circuit. If the machine takes 311 W and 4.5A from 115-V source…

Q: Ean = 12020° v; Epn = 1202 – 120° v; Een Zan = Zbn = Zen = 0.1 +j1.5 0 Line 2: Ztine a = 1+j2 0;…

Q: In the circuit shown below, V=20<0, R1=10 ohm, R2= 5 ohm, Zc=-j5, and ZL=j3 ohm. Choose the load…

Q: As shown in Figure Q1(b), two loads A and B are connected in parallel across a 1.5 kV rms 60-Hz…

A: The solution can be achieved as follows.

Q: A substation rated 1250 kVA is operating at full-load at 0.8 pf lagging and to carry an additional…

A: Inductive element consume reactive power but Capacitive elements deliver reactive power into the…

Q: |The data of the power system shown in the figure: X= 1.2 p.u. X= 0.15 p.u. G1, G2, G3: T1, T2, T3:…

A: The answer as given below;;

Q: There is a load formed by the series connection of the resistor R0 and the inductance L0 between the…

A: In this we will find maximum power deliverd to load and load impedance for this..

Q: Investigate and expose 3 applications and their importance in everyday life (real life, home,…

Q: system which consist of two power plants, the incremental cost in GHC/MWhr are dC₁ dP -= 0.17 P₁ +…

A: Given data : The given incremental cost , dC1dP1=0.17P1+140dC2dP2=0.24P2+185 The system operates…

Q: ) Norton in the form I = GNV + IN of the part of the circuit seen when looking left from the A-B…

Q: an R-L circuit takes a current of 7amp that lags behind the 231-volt source by 35elec deg. calculate…

Q: Problem 4 Two loads are connected in parallel across a 1000-V rms, 60-Hz source. One load absorbs…

Q: 0.16-henry inductance are connected in series. What is the equivalent impedance? a. 20 + j102.2…

A: Given ,here are two relays with resistance and inductance so in series they are added to find the…

Q: The actual impedance of a system is 300 Ω. The base kVA is 300 kVA, and the base voltage is 11 kV.…

Q: Q: For the following SLD, take Sg = 100 MVA and VB = 22 kV at Bus 1 to: 1. Draw the impedance…

A: 1)To find the per unit impedance on given base of 100 MVA and 22 kv - Per unit impedance of…

Q: Given: A 8 kV circuit has a load consisting of 640 N of resistance in series with 960 N of inductive…

A: the circuit is shown below, First determine the total load with the capacitor branch. To…

Q: Pzi- The of abalanced Y connected load is- Each phase of the load cousist of loL30 s2 Find the Line…

Q: For the shown Crank diagram, if the voltage at the load is equal to ER-35 Volt and the…

A: for the shown crank diagram , if the voltage at the load is equal to ER=35 volt and the…

Q: A- 3-8 50Kew, 4-pole, soH2 haß a coinding Cac) desigmed for delta connection. the coinding has 24…

A: An induction motor is an asynchronous motor it is the most commonly used AC motor. There are mainly…

Q: 10A. Calculate the power consumed of the load, load impedance and power factor of the load. c) What…

A: a. Given NP=1NS=240Rm=1 ΩXm=0.5 ΩRz=0.5 ΩXz=0.25 Ω

Q: 1. When a 2-ohm, a 4-ohm, and 6-ohm resistors are in delta connection, the equivalent resistors in…

Q: ]What happens when we encounter a circuit that has all 3 components in series? Parallel? How do we…

A: To answer above question, one should know basic circuit theory rules: Ohm's law: Ohm's law state…

Q: In an apartment with three flats fed from a 400V 60 Hz three-phase network, a 250W device in…

A: Given circuit: Line voltage

Q: A substation rated 1250 kVA is operating at full-load at 0.8 pf lagging and to carry an additional…

A: Capacitor banks are used to increase the power factor by compensating the reactive power.…

Question

The one line diagram of the system and data:
Gl and G2:reactance=0.2 p.u ,11kv, 100MVA
T1 and T2: reactance =0.05p.u, 11/132 kv
LI: reactance=0.216p.u, 132kv
L2=0.09p.u, 132kv
L3=0.09p.u, 132kv
Calculate the fault current when a three phase fault accurs at bus 5
5
L2
L3
to
L1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q: For the following OLD, take Sg = 50 MVA and VB = 22 kV at thetransmission line to find the short circuit current if a 3-ph fault occurs atthe middle of transmission line.15 MVA20 MVAX = j0.6 pu(15:35) kVG-EX = j0.3 pu25 MVA(40:15) kV15 MVA(6+j8) Q23 kVM18 kVT.LX = j0.5 puT1T2´x = j0.3 pu
17. Which section of the National Electrical Code provides the performance requirements and criteria foran effective ground-fault current path?A. 358.30B. 250.4(A)(5)C. 250.118D. 358.6
Does an open- operation, the kVA rating compared to that of the original thr-phase bank is (a) 2/3 (b) 58 (c) 1
a) Draw the sequence network and calculate the sub-transient fault current for a dead short circuit on one phase to ground at bus 4 with fault impedance j1.78 p.u for the system shown in Fig. The system data's are Machine 1: Xd”=j0.21p.u , X2=j0.4p.u; X0= j0.55p.u ; Machine 2: Xd”=j0.21p.u , X2=j0.4p.u; X0= j0.55p.u ; Transformers T1 and T2 : X1=X2=X0= j1.2p.u The transmission line reactance X1=X2= j0.21p.u and X0=0.97 p.u.
In a short circuit test on 132 kV, 3-phase system, the breaker gives the following results: Power factor of the fault = 0.45. Recovery voltage 0.9 time of full line voltage. The breaking current is symmetrical. The restriking transient has a natural frequency of 15 kHz. Calculate the rate of rise of restriking voltage (RRRV) in the following types of faults: (1) Grounded fault (2) Undergrounded fault.
1-The following sequence currents were recorded in a power system under a fault condition Ipositive=j1.5pu, Inegative=–j0pu, Izero=– j0pu. The fault is a.Three-phase b.Double Line to ground c.Line to ground d.Line to line also if this case 2- he following sequence currents were recorded in a power system under a fault condition Ipositive=j1.5pu, Inegative=j0pu, Izero=j0pu. The fault is a.Three-phase b.Double Line to ground c.Line to ground d.Line to line i uploded the houndots (book )here :https://seomidea.com/hct/nu.pdf
a) draw the reactance diagram based on values in A busbar. U=29 S=30 b) while the voltage in B busbar is 13kV, 17MW 0.85 inductive power factor in M1, 8MW 0.9 inductive power factor in M2, what should be the terminal voltage in generator? c) to have a 3 phase fault in B busbar, what should be the fault current?
The recommended limit of voltage drop on a power circuit for a single-phase supply as per IEE Wiring regulations is equal to 12 V. Then the value of supply voltage is a. 200 V b. 400 V c. 240 V d. 230 V
A 25 MVA, II kV generator has X"d=0.2 p.u. X2 = 0.3p.u. and X0=0.1 p.u. Tht neutral of generator is solidly grounded. Determine the subtransient current in the generator and the line to line voltages for subtransient condition when a Y-B-G fault occurs at the generator terminals. Assume prefault currents and fault resistance to be zero.
Short-circuit current in case of 3-phase fault in busbar A5 calculate
The busbars of a gonerating station are divided into two soctions A and B by a busbar reactor rated at 8000KVA with 9% reactive drop. On busbar A there are two generators each of 8000 KVA with 12.5% reactance and on busbar B there are two generatore each of 10,000KVA with 10% reactance. Feeders are taken. from sections A and B separately. Calculate the rupturing capacity of each foeder switchgear for 3-phase faults which may occur on any feeder. Ans: Feeder A 189 MVA; Feeder B 252 MVA
Please solve the following problems show a step by step solution. Use four decimal places. Use the default modeling for the sequences if not given Problem 2 of lecture no.7. Solve also for the phase voltage at 'c' for a double line to ground fault. A 3 phase, 11kV, 30 MVA turbo alternator has a positive equal to negative reactance of 0.15 pu and zero sequence reactance of 0.02 pu. Calculate the fault current for a line to line fault.