11) The force P is applied at d = 50 mm from the bottom as shown.Compute the normal stress at section a-a at the specific points.a200 mm200 mmB20 mm-300 mm-aIf P = 66 kN, what is the normal stress at point A in MPa (2 decimals)?.

Given data: d=50 mmP=66 kN Need to determine the normal stress at point A.

Answered: The force P is applied at d = 50 mm…

The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section a-a at the specific points. a C+ 200 mm P 200 mm di -300 mm- a B A 20 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.27P: A simply supported wood beam is subjected to point load P at mid-span. The stresses on element C are...

See similar textbooks

Related questions

Q: For the mechanism shown below, compute the magnitude of the force (F) required to break contact at…

Q: Part (A)- In a Hartnell governor, the mass of each ball is 6 kg. The lengths of ball arm and sleeve…

Q: The 55-kg cylinder is suspended from a clamping collar at C which can be positioned at any…

A: cable length = 12 m distance between the supports A and B = 10 m mass of the cylinder (m) = 55 kg

Q: In the figure, one end of a uniform beam of weight 130 N is hinged to a wall; the other end is…

A: Given dataWeight of beam = W = 130 Nθ = 34°

Q: Q/ For the mechanism shown below, compute the magnitude of the force (F) required to break contact…

A: Given:s=10 mmK=1800 N/m

Q: Q/ Find the reaction forces at point (B) 2.4 m 1.2 m 300 kg B

Q: SI/USCS Units) In a Brinell hardness test, a 1500-kg load is pressed into a specimen using a…

Q: 1.) Assume that a wing component on an airplane is made of an aluminum alloy with a plane strain…

A: Disclaimer: Since you have asked multiple question, we will solve the first question for you. If you…

Q: 2. In an aircraft refrigeration as shown in the figure below, air bled from the jet engine is at 326…

A: Simple air craft refrigeration system Neglecting ramming effect and considering inlet pressure to…

Q: Q1/A dead weight tester is used to calibrate a pressure transducer by the use of known weights…

A: Diameter of the piston, d=10 mm=0.010 mPressure required, P=200 kPa

Q: Find the stresses in A, B and C?

Q: R(S) XIS K 1 s+5 s+2 s+3 Y(s)

Q: Explain self-diffusion of nickel.

A: The transfer of a chemical from a high-concentration area to a low-concentration area is referred…

Q: A pole tilts toward the sun at an angle of 8 degrees from the vertical, and it casts a 22-ft shadow.…

Q: A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional…

Q: 1. What are the normal use or uses of this product or component? What are the normal operating…

A: Given questions: 1. What are the normal use or uses of this product or component? What are the…

Q: m 20 15 10 5 0 2 4 6 8 10 12 14 sec.

Q: critical conditions

A: False

Q: Consider the shaded area in (Figure 1). Suppose that a = 9m, k = -1 m 9 4 Figure y = kx² P IM 1 of 1…

Q: The water needs of a small farm are to be met by pumping water from a well that can supply water…

Q: 2. The CPU time requirement X of a typical job can be modeled by the following hyperexponential…

Q: Problem 2 Deduce the equations governing the dynamics of the hydraulic control system shown in the…

Q: 1. AB=X 2. A+B=X 3. X=A 4. ABC=X 5. AB+CD=X 6. AB+A=X Page | 4

Q: Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of…

Q: Under expansion flow in convergent- -10 divergent nozzle accurse with exit supersonic flow when Pb <…

A: the back pressure is lower then the exit pressure and the mass flow rate is maximum , mach number is…

Q: The simple truss is loaded by a system of forces as shown in the figure. The truss is supported by a…

Q: Prob 2. The cantilever beam below is made of steel (E200 GPa) and must support the distributed load…

Q: Q5. A 3 kw wasted energy (as a heat) from a fired system at temperature of 80°C is to be used to…

Q: 7. 8. > [၁] X

A: 1) A+B+C

Q: Two rods support the rigid bar ABC as shown in the figure. A downwards load P of 50 kN is applied at…

A: Given:P=50 KNFor BD:L=600 mmE=73 GPaA=1250 mm2For CE:L=400 mmE=200 GPaA=750 mm2

Q: cross-sectional area = 150 mm2. During testing, the following force and gage length data are…

Q: The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 230…

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A: Given data as per the question angle =710force acting upward=1.92kNForce acting on downside =1.26…

Q: A cylinder is made of steel plate is intended to be used as a container for compressed air. The…

Q: Consider the area shown in (Figure 1). Suppose that L = 5.7 in. Part A Locate the centroid (z, y) of…

Q: A cylinder is made of steel plate is intended to be used as a container for compressed air. The…

A: (1) The maximum air pressure that can be stored in the cylinder is 3.33 MPa. (2) The change in the…

Q: Q2/ In equilibrium position shown in figure below. The uniform bar (AB) has a mass of (50 kg) and…

Q: During a steady right turn, a person exerts the forces shown on the steering wheel. Note that each…

A: The moment exerted about the steering column at O: M = -1.8014 N•m ... (Clockwise)

Q: For a given material, the Young's modulus is 2.8 times that of rigidity modulus. The Poisson's ratio…

A: Given data : Modulus of rigidity=G Youngs modulus=E E=2.8×G

Q: Q-3: The nail cutter consists of the handle and the two cutting blades. Assuming the blades are pin…

Q: Q/ For the mechanism shown below, compute the magnitude of the force (F) required to break contact…

Q: A Francis turbine is to be designed to produce 27 MW at a shaft speed of 90rev/minunder an effective…

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

Q: 11- If A, B and C are three mutually exclusive events in the sample space then P(AUB UC)= a-…

A: Option (b) : P(A) +P (B)+ P(C)

Q: The 45-kg cylinder is suspended from a clamping collar at C which can be positioned at any…

A: Concept: Lami's theorem: When three coplaner forces impinge on an equilibrium point, each force is…

Q: Q/ If F1 = 250 N and F2 = 375 N are two forces, the angle between F1 and the positive y-axis is…

Q: IC ENGINE 13. Specify the main emission form multi-cylinder passenger car engine how is the…

A: The main emission from multi-passenger emission-car are NOx, HC, and CO. There are three basic…

Q: 2. Compute for the (a) dryness factor, (b) internal energy, (c) enthalpy, and (d) entropy of a…

Q: The impending motion is applied when the body is Select one: O a. Just stopped Ob. Stopped Oc. Just…

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A: Solution - Given data - F1 =2.12 KNF2 =1.25 KNM1 =0.540KN-mθ =tan-126 =18.43°

Question

11)

The force P is applied at d = 50 mm from the bottom as shown.
Compute the normal stress at section a-a at the specific points.
a
200 mm
200 mm
B
20 mm
-300 mm-
a
If P = 66 kN, what is the normal stress at point A in MPa (2 decimals)?.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
A simply supported wood beam is subjected to point load P at mid-span. The stresses on element C are known to be ??x=-92 psi and txy= -7 psi. Find the principal stresses on the element and show them on a sketch of a properly oriented clement.
The vertical load P acting on the wheel of a traveling crane is 13,000 lb. What is the average shear stress in the 1.25 in. diameter axle?
The hollow circular pipe is subjected to two forces P=1800 and F=2500. Inner and outer radius of the pipe is 24 mm and 46mm, respectively. Calculate following unknowns for point A, (a) Find all stresses and show them on the oriented element, (b) principal stress and corresponding angle, (c) maximum shear stress. Take a = 100 mm, b = 150 mm and c = 75 mm.