The graph below was generated when 20.0 mL of the unknown weak acid was titrated with 0.366 M NAOH (aq). Use this information to determine the molarity of the unknown weak acid. (assume a monoprotic acid) Give your answer to 3 significant figures. Titration Curve pH versus ml Sodium Hydroxide added 14.00 12.00 10.00 8.00 6.00 4.00 2.00 0.00 0.0 5.0 10.0 15.0 20.0 25.0 ml of sodium hydroxide Answer: на

The graph below was generated when 20.0 mL of the unknown weak acid was titrated with 0.366 M NAOH (aq). Use this information to determine the molarity of the unknown weak acid. (assume a monoprotic acid) Give your answer to 3 significant figures. Titration Curve pH versus ml Sodium Hydroxide added 14.00 12.00 10.00 8.00 6.00 4.00 2.00 0.00 0.0 5.0 10.0 15.0 20.0 25.0 ml of sodium hydroxide Answer: на

Chemistry: Principles and Practice

3rd Edition

ISBN:9780534420123

Author:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Publisher:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Chapter16: Reactions Between Acids And Bases

Section: Chapter Questions

Problem 16.24QE: Calculate the pH during the titration of 50.00 mL of 0.100 M Sr(OH)2 with 0.100 M HNO3 after 0,...

See similar textbooks

Similar questions

Another way to treat data from a pH titration is to graph the absolute value of the change in pH per change in milliliters added versus milliliters added (pH/mL versus mL added). Make this graph using your results from Exercise 61. What advantage might this method have over the traditional method for treating titration data?
Consider the following two acids: In two separate experiments the pH was measured during the titration of 5.00 mmol of each acid with 0.200 M NaOH. Each experiment showed only one stoichiometric point when the data were plotted. In one experiment the stoichiometric point was at 25.00 mL added NaOH, and in the other experiment the stoichiometric point was at 50.00 mL NaOH. Explain these results. (See Exercise 113.)
Follow the directions of Question 64. Consider two beakers: Beaker A has a weak acid(K a=1105). Beaker B has HCI. The volume and molarity of each acid in the beakers are the same. Both acids are to be titrated with a 0.1 M solution of NaOH. (a) Before titration starts (at zero time), the pH of the solution in Beaker A is the pH of the solution in Beaker B. (b) At half-neutralization (halfway to the equivalence point), the pH of the solution in Beaker A the pH of the solution in Beaker B. (c) When each solution has reached its equivalence point, the pH of the solution in Beaker A the pH of the solution in Beaker B. (d) At the equivalence point, the volume of NaOH used to titrate HCI in Beaker B the volume of NaOH used to titrate the weak acid in Beaker A.
A student intends to titrate a solution of a weak monoprotic acid with a sodium hydroxide solution but reverses the two solutions and places the weak acid solution in the buret. After 23.75 mL of the weak acid solution has been added to 50.0 mL of the 0.100 M NaOH solution, the pH of the resulting solution is 10.50. Calculate the original concentration of the solution of weak acid.
You are given the following acidbase titration data, where each point on the graph represents the pH after adding a given volume of titrant (the substance being added during the titration). a What substance is being titrated, a strong acid, strong base, weak acid, or weak base? b What is the pH at the equivalence point of the tiration? c What indicator might you use to perform this titration? Explain.
Consider the nanoscale-level representations for Question 111 of the titration of the aqueous strong acid HA with aqueous NaOH, the titrant. Water molecules and Na+ ions are omitted for clarity. Which diagram corresponds to the situation: (a) After a very small volume of titrant has been added to the initial HA solution? (b) Halfway to the equivalence point? (c) When enough titrant has been added to take the solution just past the equivalence point? (d) At the equivalence point? Nanoscale representations for Question 111.
Consider the nanoscale-level representations for Question 110 of the titration of the aqueous weak acid HX with aqueous NaOH, the titrant. Water molecules and Na+ ions are omitted for clarity. Which diagram corresponds to the situation: After a very small volume of titrant has been added to the initial HX solution? When enough titrant has been added to take the solution just past the equivalence point? Halfway to the equivalence point? At the equivalence point? Nanoscale representations for Question 110.
Explain how to choose the appropriate acid-base indicator for the titration of a weak base with a strong acid.
A monoprotic organic acid that has a molar mass of 176.1 g/mol is synthesized. Unfortunately, the acid produced is not completely pure. In addition, it is not soluble in water. A chemist weighs a 1.8451-g sample of the impure acid and adds it to 100.0 mL of 0.1050 M NaOH. The acid is soluble in the NaOH solution and reacts to consume most of the NaOH. The amount of excess NaOH is determined by titration: It takes 3.28 mL of 0.0970 M HCl to neutralize the excess NaOH. What is the purity of the original acid, in percent?
Calculate the pH after 0.10 mole of NaOH is added to 1.00 L of the solution in Exercise 31, and calculate the pH after 0.20 mole of HCl is added to 1.00 L of the solution in Exercise 31.
Calculate the pH during the titration of 50.00 mL of 0.100 M Sr(OH)2 with 0.100 M HNO3 after 0, 50.00, 100.00, and 150.00 mL nitric acid have been added. Graph the titration curve and compare with the titration curve obtained in Exercise 16.22.