The hot metal piece weighing 2.500g at 100.0°C is dropped into 40.0 mL water at 20.0 write your.answers on this page and give this to your TA before prelab lecture starts. After answering these questions, enter your answers in Bb. If for any reason, the system fails, Q1. Consider the following exercise °C. The final temperature of the system is 24.0°C. If the metal is treated as the system, the surrounding in this case is Is q(system) positive or negative? Calculate the specific heat of a solid metal (C(metal)).

The hot metal piece weighing 2.500g at 100.0°C is dropped into 40.0 mL water at 20.0 write your.answers on this page and give this to your TA before prelab lecture starts. After answering these questions, enter your answers in Bb. If for any reason, the system fails, Q1. Consider the following exercise °C. The final temperature of the system is 24.0°C. If the metal is treated as the system, the surrounding in this case is Is q(system) positive or negative? Calculate the specific heat of a solid metal (C(metal)).

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter12: Thermodynamic Processes And Thermochemistry

Section: Chapter Questions

Problem 22P

See similar textbooks

Similar questions

The following are values of heat capacity for nitrogen gas; Temp K Cv J/mol. K 300 20.8 400 20.9 500 21.2 600 21.8 700 22.4 800 23.1 900 23.7 1000 24.3 1100 24.9 Using the general formula Cv = A BT C/T2, find values of A, B, and C that fit the given data.
A chemical reaction takes place inside a flask submerged in a water bath. The water bath contains 4.70 kg of water at 37.5C. During the reaction 92.8kJ of heat flows out of the flask and into the bath. Calculate the new temperature of the water bath. Heat capacity of water is 4.18J.g-1.K-1. Round your answer to 3
A mixture of gaseous reactants is put into a cylinder, where a chemical reaction turns then into gaseaous products. the cylinder has a piston that moves in or out, as necessary, to keep a constant pressure on the mixture of 1 atm. the cylinder is also submerged in a large insulated water bath. From previous experiments, this chemical reaction is known to release 173.kJ of energy. the temperature of the water bath is monitored, and it is determined from this data that 37.2kJ of heat flows out of the system during the reaction. Is the reaction exothermic or endothermic? Does the temperature of the water bath go up or down? Does the piston move in or out? Does the gas mixture do work, or is work done on it? How much work is done on (or by) the gas mixture? Round your answer to 3 significant digits.
Enter your answer in the provided box. A quantity of 2.00×102 mL of 0.724 M HCl is mixed with2.00×102 mLof 0.362 MBa(OH)2in a constant-pressure calorimeter of negligible heat capacity. The initial temperature of the HCl andBa(OH)2solutions is the same at 20.79°C. For the process below, the heat of neutralization is −56.2 kJ/mol. What is the final temperature of the mixed solutions? H+(aq) + OH−(aq)→H2O(l) ____°C
a) A 1.60 dm3 sample of a mixture of methane gas, CH4 and oxygen gas, measured at 25 oC and 101 kPa, was allowed to react in a bomb calorimeter in which, had a heat capacity of 5.30 kJ/K altogether with its contents. The complete combustion of the methane gas to carbon dioxide gas and water caused a temperature rise in the calorimeter of 6.28 K. Given that ∆Ho c (CH4) is -560 kJ/mol. i. Define the standard enthalpy of combustion of methane ii. Write a thermochemical equation for the combustion of methane iii. Knowing the ∆Ho c of methane, calculate the number of mole of methane in the mixture. iv. Calculate the total moles of gases in the calorimeter.
The internal energy, E, of a system is the sum of the kinetic and potential energy of all of components of the system. What is ΔE (in kJ) for a gaseous system that increases the kinetic energy of it particles using 9,904. J of heat from surroundings and changes the potential energy by doing 5.38 kcal of work against the atmosphere at the same time? (Enter your answer with the correct sign and with two decimal places and no units.) {Hint: be cautious of the signs of the values and units; recall 1 cal = 4.184 J. }
A system consists of 50.0 g of liquid water. The water is vaporized to form steam at 1.00 bar and 100.°C. How much work (in kJ) is done by the system during this process? The density of liquid water is 0.959 g mL−1 at 100.°C.
Nitroglycerin (C3H5N3O9), a liquid at room temperature (25 oC) and atmospheric pressure (1.01325 x 105 Pa) is used to relieve angina. It may undergo decomposition under these same conditions to form nitrogen, carbon dioxide, oxygen and water, with an enthalpy of decomposition of -1541 kJ mol-1The standard enthalpies of formation of water and carbon dioxide are -285.9 kJ mol-1 and -393.5 kJ mol-1 respectively Calculate the work done when 1.0 mole of nitroglycerin decomposes and additionally explain the significance of the sign.
Under a constant pressure of 1.00 atm, at 25.00oC, the combustion of 1.136 g of C6H12O3(l) raises the temperature of 2.000 kg of water by 2.617 degrees Celsius. Combustion is the reaction of a substance with O2(g) to give CO2(g) and H2O(l). The specific heat capacity of water is 4.184 J K-1 g-1. Ignore the heat capacities of any containers.With the help of the data above, find the values of ΔH, ΔU, Q, and W for the combustion of 1.000 mol of C6H12O3(l) in a steel container of constant volume at 25.00oC.
A gas confined in a cylinder by a piston. It is taken from state A to state B along the path ACB as shown on the PV diagram below. The process from A to C is constant pressure, and the system receives 50 J of work and give up 25 J of heat to the surroundings. The process from C to B is constant volume and the system receives 75 J of heat. The return path from B to A is adiabatic. How much work is exchanged with the surroundings for the adiabatic path? Assume all processes are reversible.
Consider a piston (or box) pressurized with air. Suppose you compress the piston so that the final volume is half the starting volume but the temperature remains the same. For a reversible process, i) would the work done on the system be the same or change whether you modeled the gas ideal or real? ii) For an irreversible process, would the work done on the system be the same or change whether you modeled the gas as ideal or real assumng that you applied the same external force for compression? Explain your answer.
An oxyacetylene flame is often used in the welding of metals. Estimate the flame temperature produced by the reaction 2C2H2 (?) + 5O2 (?) ⟶ 4CO2 (?) + 2H2O(?) a) Using appropriate tabulated data (heats of formation) determine the heat of reaction at 298K. b) Now assume this reaction occurs at 2270K. Estimate the approximate enthalpy at the higher temperature using the heat capacities of these substances.