The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from stainless steel 304 has a rectangular cross section that is 12 mm wide by 4 mm thick. The bolt is tightened so that it has a tension of 1750 N. Neglect the hole in the link. The modulus of elasticity are, EL2 = 200 GPa and E304 = 193 GPa. (a) Determine the strain energy in the link AB due to bending. (b) Determine the strain energy in the bolt due to axial load.

The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from stainless steel 304 has a rectangular cross section that is 12 mm wide by 4 mm thick. The bolt is tightened so that it has a tension of 1750 N. Neglect the hole in the link. The modulus of elasticity are, EL2 = 200 GPa and E304 = 193 GPa. (a) Determine the strain energy in the link AB due to bending. (b) Determine the strain energy in the bolt due to axial load.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.7.11P: A block B is pushed against three springs by a force P (see figure). The middle spring has a...

See similar textbooks

Similar questions

A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the glass. The height of the joint is/p = 0.5 in, its length is L = 30 in, and its thickness is/ = 0.5 in. Shear force of I' = 25 kips is applied to the joint. Calculate the displacement of the joint if the shear modulus of elasticity G of the epoxy is 100 ksi. Calculate the average shear strain in the epoxy.
A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
A prismatic bar in tension has a length L = 2.0 m and cross-sectional area A =249 mn2. The material of the bar has the stress-strain curve shown in the figure. Determi ne t he elongation 5 of the bar for each of the following axial loads: P = 10 kN, 20 kN, 30 kN, 40 kN. and 45 kN. From these results, plot a diagram of load P versus elongation 5 (load-displacement diagram).
A bar with a circular cross section having two different diameters d and 2d is shown in the figure. The length of each segment of the bar is L/2T and the modulus of elasticity of the material is E. (a) Obtain a formula for the strain energy U of the bar due to the load P. (b) Calculate the strain energy if the load P = 27 kN, the length L = 600 mm, the diameter d = 40 mm, and the material is brass with E = 105 GPa.
Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
The statically indeterminate structure shown in the figure consists of a horizontal rigid bar AB supported by five equally spaced springs. Springs l, 2, and 3 have stiff nesses 3k, 5k. and k, respectively. When unstressed, the lower ends of all Five springs lie along: a horizontal line. Bar AB. which has weight W, causes the springs to elongate by an amount S. (a) Obtain a formula For the total strain energy of the springs in terms of the downward displacement d of the bar. (b) Obtain a formula for the displacement S by equating the strain energy of the springs to the work done by the weight W.
Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v = 0.33. P = 96 kips. Pt,. = 24 kips. and V =18 kips. For part (b) of Problem 7.5-12, assume that the required strain energy stored is 640 in.-lb. In part (c). the change in volume cannot exceed 0.05%.
A 4.75-in, outside diameter polyethylene pipe designed to carry chemical waste is placed in a trench and bent around a quarter-circular 90° bend (see figure). The bent section of the pipe is 52 ft long. Determine the maximum compressive strain If the normal strain cannot exceed 6.1 × 10-3 , what is the maximum diameter of the pipe? If d = 4.75 in., what is the minimum acceptable length of the bent section of the pipe?
A block B is pushed against three springs by a force P (see figure). The middle spring has a stillness K1and the outer springs each have stiffness k^. Initially, the springs are unstressed, and the middle spring is longer than the outer springs (the difference in length is denoted s). (a) Draw a force-displacement diagram with the force P as ordinate and the displacement x of the block as abscissa. (b) From the diagram, determine the strain energy U1 of the springs when x = 2s. (c) Explain why the strain energy E, is not equal to P
A brass cube of 48 mm on each edge is comp ressed in two perpendicular directions by forces P = 160 kN (see figure). (a) Calculate the change ...IV in the volume of the cube and the strain energy U stored in the cube. assuming E = 100 GPa and i’ = 0.34. (b) Repeat part (a) if the cube is made of an alumim um alloy with E = 73 GPa and v = 0.33.
Solve the preceding problem if the plate is made of aluminum with E = 72 GPa and Poisson’s ratio v = 0.33. The plate is loaded in biaxial stress with normal stress sx= 79 MPa, angle Ø = 18°, and the strain measured by the gage is e = 925 × 10-6.
A three-story steel column in a building supports roof and floor loads as shown in the figure. The story height H is 10.5 ft. the cross-sectional area A of the column is 15.5 in2, and the modulus of elasticity E of the steel is 30 × 106 psi. Calculate the strain energy U of the column assuming P1= 40 kips and P2= P3= 60 kips.