The laminar row takes place between closely spaced parallel plates as shown in figure below. The velocity profile is given by u = V = v/h. The gap height, h is 5 mm and the space is filled with oil (specific gravity = 0.86. viscosity m = 2 x 10-1¹ N-s/m²). The bottom plate is stationary and the top plate moves with a steady velocity of V = 5 cm/s. The area of the plate is 0.25 m². FL h Stationary The power require to keep the plate in steady motion is

The laminar row takes place between closely spaced parallel plates as shown in figure below. The velocity profile is given by u = V = v/h. The gap height, h is 5 mm and the space is filled with oil (specific gravity = 0.86. viscosity m = 2 x 10-1¹ N-s/m²). The bottom plate is stationary and the top plate moves with a steady velocity of V = 5 cm/s. The area of the plate is 0.25 m². FL h Stationary The power require to keep the plate in steady motion is

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

A horizontal reducing bend deflected at 110° has a diameter of 250mm upstream and 100mm downstream. A fluid (SG=0.90) enters the bend with a velocity of 3.70 m/s and a pressure of 300 kPa. Neglecting any energy losses, determine the horizontal and vertical component of the force required to hold the bend in place in kN.
The tank shown in the figure is 3 m wide into the paper. Neglect atmospheric pressure. Use ?????? = 9.79 kN/m³. Determine the following: A. vertical component of the total hydrostatic force on the quarter circle panel AB in kN B. Resultant hydrostatic force acting on the quarter circle panel AB in kN C. Angle that the resultant hydrostatic force make with the horizontal in degrees.
From the given figure. Determine the total active lateral pressure at the interface in kPa.
A plate moves 10 cm/s to the right is 0.6 cm above a stagnant wall. The fluid bet. the plate and the wall has a viscosity of 1.8 cP. Compute the shear rate.
Fluid Mechanics Problem 1) A rectangular gate 3 meters high and 1.2 meters wide is hinged at the top. A force to keep the gate closed is applied at the bottom with an angle of 45 degrees with the veritcal. Compute the following if the water surface is 0.9 meters below the top of the gate. Use 9.81kN/m^3 as water's specific weight. a. the total hydrostatic force acting on the gate in kN. b. the distance of the total hydrostatic force measured from the liquid surface in meter. c. the magnitude of the force at the bottom of the gate in kN. 2) Use 9.81kN/m^3 as water's specific weight. Consider the rectangular gate shown in the figure. If the gate has a length of 2 meters, determine: a. the force exerted by the water on the left side of the gate in kN. b. the force exerted by the water on the right side of the gate in kN. c. the horizontal force at B required to turn the gate about the hinge in kN.
In the system given in three dimensions in the figure, L=6 m and all the bars have circular cross-sections. As can be seen, the carrier system is exposed to a force of P=250 kN in the –z direction from the D point. Since the safety stress of the material is 100000 kN/m², what is the smallest radius of the section according to the Tresca assumption?
A square plate having one of its side equal to 3m is immerse in a water surface in a vertical position such that the two edges of the square would be horizontal in order that the center of pressure shall be 10 cm from the center of gravity. a) How far below the water surface should the upper plate be submerged? b.) What is the distance of the center of pressure from the water surface. c) Retermine the total hydrostatic force acting on the plate at this postion.
A cylindrical tank has a mean radius of 40 cm and thickness of 10 cm. It is subjected to an external pressure of 140 kg/cm2 and maximum internal pressure is 900 kg/cm2 . Determine the maximum internal tangential stress of the tank. A. 3,884.7 kg/cm2 C. 1.7684 kg/cm2 B. 4,623.6 kg/cm2 D. 2,947.5 kg/cm2
PROBLEM 1: The homogeneous structure shown weighs 21.45 kN per square meter of cross-section. The structure is subject to horizontal uniformly distributed load P1 and triangularly distributed load P2 perpendicular to side AB. Given: H1 = 9 m; H2 = 6 m; H3 = 12 m X1 = 6 m; X2 = 5 m P1 = 220 kN/m; P2 = 280 kN/m 4 Magnitude of resultant, R 4314.04 5 Angle of resultant direction from x-axis, θx 86.01 6 Distance of resultant from C measured along line CD, X 9.116
In figure below compute the net force exerted on the hemispherical shape located at the bottom of the container
A hollow circular plate of 2m external diameter and 1m internal diameter is immersed vertically in water such that the center of the plate is 4m deep from water surface. Find the depth of the center of pressure of the plate.
Water flows at a rate of 120 L/s in a 30 cm diameter horizontal pipe connected to a 20 cm diameter pipe through a vertical reducer bend. The change in water direction of the reducing bend is 120o. The vertical distance between the entrance and outlet of the bend is 1.5 m and the pressure at its entrance is 70KPa. The total weight of the bend material and water contained in it is 90 kg. Sketch the forces involve in the pipe flow analysis