An universal coupling is used to connect two mild steel shafts transmitting a torque of 6000 N-m. Assum- ing that the shafts are subjected to torsion only, find the diameter of the shaft and the pin. The allowable shear stresses for the shaft and pin may be taken as 55 MPa and 30 MPa respectively. |Ans. d=85 mm; d = 40 mm|

An universal coupling is used to connect two mild steel shafts transmitting a torque of 6000 N-m. Assum- ing that the shafts are subjected to torsion only, find the diameter of the shaft and the pin. The allowable shear stresses for the shaft and pin may be taken as 55 MPa and 30 MPa respectively. |Ans. d=85 mm; d = 40 mm|

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) A flange coupling connects two 50mm shafts. The flanges are fitted with 4 bolts of SAE1040 steel on an 80mm bolt circle. The shaft runs @ 360 rpm & transmits 30kW. Assume a factor of safety 4, ultimate tension of 490x103 kPa; ultimate shear of 400x103 kPa, determine: (a) the torque transmitted in kN-m; (b) the minimum diameter of the bolts required based on commercial sizes; (c) the minimum thickness of the flange.
A flange coupling connects two 2” diameter shafts. The flanges are fitted with 6 bolts of SAE 1040 steel on a 7” bolt circle. The shafts runs at 300 rpm and transmits 45 hp. Assume a factor of safety of 5, ultimate tension of 70,000 psi, and ultimate shear of 55,000 psi. Determine: a) The torque transmitted, in-lbs b) The force applied per bolt, lbs c) The diameter of the bolt required, in d) The thickness of flanged to be used, in
The allowable stresses for the splice shown are the following: 150 MPa for shear of rivets, 1.35Fy for bearing,0.60Fy for tension and Fy = 250 MPa. Note: rivet holes are 2 mm bigger than the rivet diameter and the middleplate is 20 mm thick. Find the diameter of the rivets so that the joint capacity due to shear approximately equal to the bearingcapacity.a. 25.4 mm c. 28.65 mmb. 30.79 mm d. 36.97 mm Find the maximum safe value of P without exceeding the allowable shearing stressa. 773.6 kN c. 938.3 kNb. 878.1 kN d. 848.2 kN Find the maximum safe value of P without exceeding the allowable tensile stress.a. 579.3 kN c. 716.1 kNb. 495.5 kN d. 692.5 kN
Design a rigid flange coupling to transmit a torque of 250N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Torque = 257N-m
Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Answer in Word please
Show whether it is safe by calculating the stresses at point A according to the Tresca Criteria. (Diameter: 20 mm, σA = 320 MPa)
Q1. Design and draw a protective type of cast iron flange coupling for a steel shaft transmitting ‘P’ kW at ‘N’ r.p.m. and having an allowable shear stress of 40 MPa. The working stress in the bolts should not exceed 30 MPa. Assume that the same material is used for shaft and key and that the crushing stress is twice the value of its shear stress. The maximum torque is 25% greater than the full load torque. The shear stress for cast iron is 14 MPa. Power P in KW=22 , speed in rpm= 550
An AISI 1035 CD steel tube has an OD = 45 mm and a wall thickness of 5 mm. What maximum external pressure can this tube withstand if the largest principal normal stress is not to exceed 80 % of the minimum yield strength of the material? Assume ?? = 0.
Question twoa) Shafts and tubes having circular cross sections cannot be used to transmit powerdeveloped by a machine. True or False? b) Explain the concept of torsion. c) If the applied torque on shaft CD is T = 75 N.m, determine the absolute maximumshear stress in each shaft. The bearings B, C, and D allow free rotation of the shafts,and the motor holds the shafts fixed from rotating
(7) The drive of an outboard motor which rotates @ 5,000rpm is supported by a spline in the crankshaft @ the upper end & bearing @ the lower end 560mm apart. (a) If the engine develops 15kW @ this speed, what is the diameter of the solid steel shaft to use? The allowable torsional stress is 80N/mm2 .
Q1. Design and draw a protective type of cast iron flange coupling for a steel shaft transmitting ‘P’ kW at ‘N’ r.p.m. and having an allowable shear stress of 40 MPa. The working stress in the bolts should not exceed 30 MPa. Assume that the same material is used for shaft and key and that the crushing stress is twice the value of its shear stress. The maximum torque is 25% greater than the full load torque. The shear stress for cast iron is 14 MPa. Power P in KN=22 , Speed N in rpm=555
The flange coupling for two shafts made of plain carbon steel to be   connected. The shafts transmitting a toque of 600 N-m. Assume the following   permissible stresses for the coupling components: Shaft — Permissible shear stress = 35 MPa Keys — Rectangular formed end sunk key having permissible compressive strength = 60 MPa Bolts — Six numbers made of steel having permissible shear stress = 28 MPa Pitch circle diameter of bolts = 1.6 × Diameter of shaft   1. diameter of shaft =44.36 2. Hub length =67.5 3. Hub diameter 90 mm Calculate: 2. thickness of flange; 3. Diameter of flange 4. Width of key 5. Thickness of key 5. Diameter of bolt; 6. Crashing stress in bolt