(a) An epicyclic gear has a fixed sun gear (B) with 200 teeth. The planet gear (C) has 40 teethCompounde with gear (D) (140 teeth). The input shaft delivers 400 W at 3600 rev/min. the gearbox efficiency is 70%. Calculate the following:I. The number of teeth on (E).II. The gear box ratioIII. The output speed and its directionIV. The holding torque.DInputOutputD

Given: B=200 teeth C=40 teeth D=140 teeth Pinput=400 W box efficiency= 70% To determine: The number…

Answered: The number of teeth on (E). The gear…

Engineering

Mechanical Engineering

The number of teeth on (E). The gear box ratio The output speed and its direction The holding torque.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The torque on shaft D is most likely: 2015 lb in 105 lb in 250 lb in 630 lb in
The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The expected rotational speed on shaft E is most likely: 375 rpm 600 rpm 1250 rpm 3000 rpm
Solve this problem in spur gearsA 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressureangle and a diametral pitch of 32. Determine the base pitch and the contact ratio. Also,calculate theaddendum, dedendum, circular pitch, tooth thickness, and the base diameter for the pinion and gear. Ifthe center distance isincreased by 0.125 in., what are the new valuesfor thecontact ratio and thepressureangle with complete solution and write in hand writing thank you
Provide very clear and complete solution and diagam. SITUATIONAL PROBLEM: Two shafts are connected by spur gears. The pitch radii of the gears A and B are 200 mm and 860 mm respectively. If shaft A makes 350rpm and is subjected to twisting moment of 250 N-m. Pressure angle is 14.5 degree. What is: a.) Rpm of gear B b.) Torque in shaft B (in Newton meter). c.) Separation load of two gears (in newtons). d.) Total load on gears (in newtons).
For a pair of spur gears, one design decision is to specify the pressure angles. Please select the common values of pressure angle per textbook. 300 200 250
Epicyclic gear box is shown in Figure.2, the gear box has outer gear C with 120 teeth, B has 50, D has 50 and E has 120.1. Calculate the gear box ratio2. Find the output speed and holding torque of the gear box, if the input gear has 1570 ??? clockwise, the input power 28.5 ?? and the efficiency is 85.5%3. You have engaged in open discussion in which you have to evaluate the conditions needed for an epicyclic gear train to become a differential. Using appropriate schematic and hand sketch show how a differential works in this application. Also, explain what needed to convert the gearbox in Figure.3 to Simple epicyclic differential
Design A two stage spur gear reduction unit with 20- Deg full depth involute teeth. The input shaft rotates at 1440 rpm and receives 10 kW power. The speed of the output shaft should be approximately 180 rpm plus minus 5 rpm , All gears are made of steel and have the same module . Determine appropriate number of teeth of the gears in the unit .
For the gear train illustrated in Figure, determine the output speed and direction of rotation if the input shaft rotates at 1490 rpm clockwise. Gears A to D have a module of 1.5 and gears E to H a module of 2. TA=20 teeth, TD=38 teeth, TE=18 teeth, TG=18 teeth, TH=30 teeth, dB=67.5mm, dC=27 mm and dF =56 mm.
Two straight-toothed bevel gears mesh with a shaft angle of 90° and a diametral pitch of 5. The pinion has 20 teeth, and the gear ratio is 2:1. The addendum and dedendum are the same as for 20 stub teeth. For the gear, determine the pitch radius, cone angle, outside diameter, cone distance, and face width.
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. Calculate the contact ratio ε with the standard center distance a, 68.75mm. ε=( )
You design a gearbox with a gear ratio of 5 (GR=5=TGB/Tm) to pull a load (FL) of 76 lbf using a motor and winch (rw=0.25 inches). What is the torque experienced by your motor when pulling the mass up at a constant speed in lbf ft? Note the units