Select the correct combination from the given below statements 1.Clutch is a machine member used only to engage a driving shaft to a driven shaft. 2.The two intersecting shafts are connected by using bevel gear. 3.When there are less than two gear on a shaft, it is called a compound gear train. 4.The non-parallel and non-intersecting shafts are connected by using worm gear.

Select the correct combination from the given below statements 1.Clutch is a machine member used only to engage a driving shaft to a driven shaft. 2.The two intersecting shafts are connected by using bevel gear. 3.When there are less than two gear on a shaft, it is called a compound gear train. 4.The non-parallel and non-intersecting shafts are connected by using worm gear.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pair of straight bevel gear consists of a pinion having 36 teeth and a gear having88 teeth. If the shaft angle is 70o, determine (a) the pitch angle of the pinion in degrees,and (b) the pitch angle of the gear in degrees.
A reverted gear train with a speed ratio of 12 consists of four gear wheels. Gear A has a module pitch of 3mm and is meshed with gear B. Whereas gear C that is meshed with gear D has a module pitch of 2.5mm. Gear B and C form a compound gear system. The distance between axis of rotation of driving gear A and driven gear B is equal to 200mm. If gear A has 24 teeth, determine the suitable number of teeth for all gears.
The teeth of the gear arrangement have Gear A=40teeth, Gear B=70 teeth and Gear C= 50teeth, a pinion (driver Gear) that rotates at 625 rpm, and idler Gear B and a driven gear (Gear C). The gears have a module of 5mm and a pressure angle of 200. Find the pitch diameter of gear C in mm.
The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating at a speed of 1200 revolutions per minute. It must increase the torque received at its input shaft 16 times. Spur gears with 20° pressure angle should be used. Input and output shafts should be aligned. The transmission should take up as little space as possible. The distance between the centers of the input shaft and the intermediate shaft (the one that loads gears 3 and 4) should be 10 inches. Determine the magnitude of the radial load that gear 4 exerts on gear 4. Write your answer in pounds.
Two parallel shaft connected by spur gears turn in the same direction and having a speedratio of SR = 4.72 (a) What is the distance of the two shaft, in mm, if the smaller gear is170 mm in diameter? (b) What is the diameter of the larger gear in mm?
An epicyclic gear train has 3 shafts A,B and CA is an input shaft running at 100 rpm clockwise. B is an output shaft running at 250 rpm clockwise. Torque on A is 50 kNm (clockwise). C is a fixed shaft. The torque to fix C
Helical Gears, Bevel Gears, and Wormgearing 3
Question 1 A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 if its gearbox 5th gear is selected. The gear’s teeth are of involute form with a module of 8 mm, an addendum is double the module, and the pressure angle is equal to 20°. 1(a). If the driving shaft of the front wheels of the truck is connected to the output shaft of the gearbox, determine the number of teeth on the pinion to avoid interference and the corresponding number of teeth on the gear wheel. 1(b) Calculate the gear maximum velocity of sliding.
A bicycle's gear ratio is the number of times the freewheel turns for every one turn of the chainwheel (see figure). The back half of a bicycle is given. A line labeled "Freewheel" is pointing at the center of the rear wheel. A line labeled "Chainwheel" is pointing to the center piece connecting the two pedals. The table shows the numbers of teeth in the freewheel and the chainwheel for the first five gears of an 18-speed touring bicycle. The chainwheel completes one rotation for each gear. GearNumber Number ofTeeth inFreewheel Number ofTeeth inChainwheel 1 32 24 2 26 24 3 22 24 4 32 40 5 19 24 Find the angle through which the freewheel turns for each gear. Give your answers in both degrees and radians. (Round your answers to one decimal place.) gear 1 = rad= gear 2= ° rad= gear 3= ° rad= gear 4= ° rad= gear 5= ° rad=
State two advantages of a compound gear train over a simple gear train
Figure shown below illustrates the gears in a speed-change gearbox used in machine tool applications. By sliding the cluster gears on shafts Band C, nine speed changes can be obtained as shown in Table given below. The problem of the machine tool designer is to select tooth numbers for the various gears (2 to 10) so as to produce a reasonable distribution of speeds for the output shaft. The gears 2, 6 and 9 are having 20, 25 and 50 teeth respectively. The input shaft speed is 450 rpm and the output speed can vary from 137 rpm to 580 rpm depending on the sequence of the gears. If the output speed obtained through the gear sequence 2-5-5-8 is 257 rpm and if the minimum and maximum number of teeth in the gear system are 20 and 50 respectively, (i) Suitable tooth numbers for the remaining gears (3,4,5,7,8 & 10)
Two mating external 8-pitch, 20o , spur gears have 24 and 64 teeth. Determine the contact ratio.