The olive oil is flowing between the two parallel plates which has 0.072 m diameter.The lower and upper plates are being pulled at a relative velocity of 0.45 m/s and 0.13m/s. The olive oil viscosity is 3.2x10-2 Pa-s at 323 °K. Calculate the shear stress and theshear rate for olive oil. If soybean oil having a viscosity of 1.123 kg/m.s was usedinstead of olive oil, what would be the new relative velocity in m/s?

Given data:-distance between two plates, D=0.072mviscosity of olive oil,…

The olive oil is flowing between the two parallel plates which has 0.072 m diameter. The lower and upper plates are being pulled at a relative velocity of 0.45 m/s and 0.13 m/s. The olive oil viscosity is 3.2x10? Pa-s at 323 °K. Calculate the shear stress and the shear rate for olive oil. If soybean oil having a viscosity of 1.123 kg/m.s was used instead of olive oil, what would be the new relative velocity in m/s?

The olive oil is flowing between the two parallel plates which has 0.072 m diameter. The lower and upper plates are being pulled at a relative velocity of 0.45 m/s and 0.13 m/s. The olive oil viscosity is 3.2x10? Pa-s at 323 °K. Calculate the shear stress and the shear rate for olive oil. If soybean oil having a viscosity of 1.123 kg/m.s was used instead of olive oil, what would be the new relative velocity in m/s?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Glycerin is flowing between two parallel plates with a maximum centerline velocity of 0.6 m/s. Determine the shear stress at the plate surfaces if a parabolic velocity distribution is assumed.
40-mm-diameter shaft is pulled through a cylindrical bearing as shown in the figure. The lubricant that fills the 0.4mm gap between the shaft and bearing is oil having a kinematic viscosity of 6×10-4 m2 /s and a specific gravity of 0.91. Determine the force P required to pull the shaft at a velocity of 4m/s. Assume the velocity distribution in the gap is linear.
The velocity through the centre-line of a 150 mm diameter pipe conveying oil under laminar flow conditions is 3 m/s. The viscosity of the oil is 1.2 poises and its density if 900 kg/m3 . Confirm that the flow is laminar and determine (a) the quantity flowing in dm³/s, and (b) the shear stress in the oil at the pipe wall in N/m²
Crude oil having a viscosity of 9.52 x 10(-4) lb-s/ft2 is contained between parallel plates. The bottom plate is fixed and upper plate moves when a forced P (lb) is applied. If the distance between the two plates is 0.1 in., what value of P is required to translate the plate with a velocity of 3 ft/s? The effective area of the upper plate is 200 in2.
Oil with a viscosity of 30 cp and density of 600 lb/ft³ flows through a ½ in ID tube. Determine the velocity in ft/s in which the flow is laminar.A. 13.1B. 169C. 87.2D. 0.63
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 m²/s and SG-0.9. A. Find the frictional resistance exerted by the oil on the shaft in Newtons (N). B. If the shaft in the problem above is fixed axially and rotated inside the sleeve at 2000 rpm, determine the resisting torque exerted by the oil and the power required to rotate the shaft in kilowatts (kW).
Water flowing in a straight cylinder tube with radius of 3mm, has a maximum velocity U0=15cm/s. If the density and viscosity of the water are 1000kg/m3 and 1.0 x 10 -3 (Pa.s), and the flow is fully developed with a profile of u=U0(1-(r/a)2), calculate the Reynold’s number of the flow; calculate the mass flow rate in units of kg/s in the tube If the tube has a length of 50cm, calculate the flow resistance force of the tube wall imposed to the flow.
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 ?2/? and SG=0.9. Find the frictional resistance exerted by the oil on the shaft in Newtons (N). And when the shaft is fixed axially and rotated inside the sleeve at 2000 rpm, determine the resisting torque exerted by the oil and the power required to rotate the shaft in kiloWatts (kW).
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = Answer J / kg. c. Energy Loss at curves = Answer J / kg. d. Total energy to overcome friction = Answer J / kg. e. Energy to increase water according to height = Answer J / kg. f. The theoretical energy requirement for the pump is kg ethanol / second = Answer J / kg. g. Actual pump power requirement = Answer watt.
Q1. Water flowing through a pipe has a dynamic viscosity of 8.9 x 10-4 Pas and a density of 1000 kg/m3. The pipe has an internal diameter of 0.0055 m What average speed must the water flow stay below for the Reynolds number of the flow to stay below 2300? Above what average speed of water flow will the Reynolds number exceed 2900?
Determine the terminal velocity of a raindrop having a diameter of 30 x 10-5 if the density of air is 1.2 kg/m3 and having a dynamic viscosity of 18 x 10-6 N.s/m2.
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = AnswerJ / kg. c. Losing Energy at curves = AnswerJ / kg. d. Total energy to overcome friction = AnswerJ / kg. e. Energy to increase water according to height = AnswerJ / kg. f. The theoretical energy requirement of the pump ethanol / second = AnswerJ / kg. g. Actual pump power requirement = Answerwatt.