Answered: The parabolic shaped gate with a width…

Name: The parabolic shaped gate with a width of 6 m shown below is hinged a
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The parabolic shaped gate with a width of 6 m shown below is hinged at point B. Computefor the force F needed to keep the gate stationary.Water12 mOil, SG = 1.79m27 m

Engineering

Mechanical Engineering

The parabolic shaped gate with a width of 6 m shown below is hinged at point B. Compute for the force F needed to keep the gate stationary. Water Oil, SG = 1.7 9 m 12 m 27 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
A 6-in. diameter hole is drilled in the conical frustum. Calculate the volume and the surface area of the resulting body.
EMERGENCY!!!! The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation of the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the lid (D = 4 m). If the weight of the lid is neglected, it is necessary to keep the lid in balance. Find the size of the force (Fa) required, as shown. Take the density of the water as 999 kg / m3.
Determine the location of the total hydrostatic force from thr bottom surface and the top surface acting on the 2m x 4m gate shown on the illustration.
plzzzzzzz help What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is 1000 kg/m3 and the density of the block is 8000 kg/m3. The specific gravity of oil is 0.9. The depth of the gate is not required. The external force that effects the gate at point A is Fe=3000 N, while the hydrostatic force Fh=9313.8 N
EMERGENCY!!!! The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation for the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the cover (D = 4 m). Find the magnitude of the applied force (Fa) as shown.
The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation of the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the cover is D = 4 m. Find the magnitude of the applied force (Fa) as shown. Take the density of water as 999kg / m3.
The cross section of a rectangular AB of width 2.5 m hinged along A is shown in the figurebelow. The weight of the gate is 55 kg, and it is used to retain the water at depth 3.3m.Calculate the minimum force R at B to hold the gate.
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown . The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B. Using appropriate software, investigate the effect of water depth on the force exerted on the plate by the ridge. Let the water depth vary from 0 to 5 m in increments of 0.5 m. Tabulate and plot your results.
A 4-m-long quarter-circular gate of radius 4 m and of negligible weight is hinged about its upper edge A, as shown in the figure. The gate controls the flow of water over the ledge at B, where the gate is pressed by a spring. Determine the minimum spring force (in N) required to keep the gate closed when the water level rises to A at the upper edge of the gate. Round your answer to 2 decimal places.
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown in Figure. The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B.Determine the force exerted on the plate by the ridge.
A small barge is being used to transport trucks across a river. If the barge is 10.00 m long by 8.00 m wide and sinks an additional 3.70 cm into the river when a loaded truck pulls onto it, determine the weight of the truck and load.