The "Established Datum" for number 2 and 3 are marked incorrect. Can you please help me with those two. Please refer to the image below. Workshop Exercise 6.3 - Datum Feature ExerciseThe part below has a variety of features that arelabeled as datum features. Assume all are primarydatum features and the datum features of size applyYat RMB.Next to the datum feature in the table below,identify if it establishes a point, axis, plane, or somecombination of these datums. Also list the namesWof translational (x,y,z) and rotational (u,v,w)degrees of freedom constrained by the datumfeature. See the isometric view to the right for thelabeled degrees of freedom.+.0052X Ф.250-.002+.600 ±.0040.005.300±.002H.-0.600±.002Ø.682±.002.002AJ4. Center Plane5. Axis & 2 Planes6. Axis & Plane2. Axis3. Plane1. PointEstablishedConstrained Degrees of FreedomPrimaryDatiDatum FeatureDatumTranslations (x,y,z)Rotations (u,v,w)AV, WX 2.V,WBС-Е3.4.DF35.G3.u,W6.7.H.X,YZ8.J1.xx

The part below has a variety of features that are labeled as datum features. Assume all are primary datum features and the datum features of size apply V at RMB. Next to the datum feature in the table below, W identify if it establishes a point, axis, plane, or some combination of these datums. Also list the names of translational (x,y,z) and rotational (u,v,w) degrees of freedom constrained by the datum feature. See the isometric view to the right for the labeled degrees of freedom. u +.005 2X Ø.250 -002 .600 ±.004 O9.005 .300±.002 Ø.600±.002 Ø.682±.002 .002 A 4. Center Plane 5. Axis & 2 Planes 6. Axis & Plane 2. Axis 3. Plane 1. Point Established Constrained Degrees of Freedom Primary Datum Feature Datum Translations (x,y,z) Rotations (u,v,w) A 3. V, W 1. V,W 2. X 3. C-E 4. 3. 4. D F 5. 3 ら 6. G 7. H X, YZ 8. J

The part below has a variety of features that are labeled as datum features. Assume all are primary datum features and the datum features of size apply V at RMB. Next to the datum feature in the table below, W identify if it establishes a point, axis, plane, or some combination of these datums. Also list the names of translational (x,y,z) and rotational (u,v,w) degrees of freedom constrained by the datum feature. See the isometric view to the right for the labeled degrees of freedom. u +.005 2X Ø.250 -002 .600 ±.004 O9.005 .300±.002 Ø.600±.002 Ø.682±.002 .002 A 4. Center Plane 5. Axis & 2 Planes 6. Axis & Plane 2. Axis 3. Plane 1. Point Established Constrained Degrees of Freedom Primary Datum Feature Datum Translations (x,y,z) Rotations (u,v,w) A 3. V, W 1. V,W 2. X 3. C-E 4. 3. 4. D F 5. 3 ら 6. G 7. H X, YZ 8. J

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need help filling out this chart. The part below has a variety of features that are labeled at datum features. Assume all are primary datum features and the datum features of size apply at RMB. Next to the datum feature in the table below, identify if it establishes a point, axis, plane, or some combination of these datums. Also list the names of translational (x,y,z) and rotational (u,v,w) degrees of freedom constrained by the datum feature. Please refer to the attached image for the graphic and table.
I need help filling in the remainder blanks in the chart attached. Next to each feature control fram, identify the degrees of freedom (x,y,z,u,v,w) constrained by each referenced datum feature.
For all three objects represented in axonometric view, you have to create: - three orthogonal views ( front, top and side) - put all necessary dimension lines on all the orthogonal views - create an oblique axonometric view
The title of our study is "Design and Fabrication of an Agricultural Spraying Attachment for an Autonomous Rover" we need help in the machine design part of our study, specifically Pump selection, battery selection, and center of gravity computation Rover weight capacity 35 kilo grams (payload) Rover measurements: Wheel distance - 14.5 inches and 8.5 inches Rover platform size (width & length) 14.4 inches x 10.4 inches Height- 15.8 inches
Dimension this object.
In a rotating body, if it rotates at 2355 revolutions per minute.What would be the angular velocity ? the angular velocity of the rotating body in rad/sec is
question from ENGINEERING DRAWING BY N.D BHATT Draw rough sketch of front , Top and side view of following 3D model using first angleprojection?
pls. see the attached photo, please help me huhu
Help me solve this ENGINEERING GRAPHICS question Use 0.25 cartesian paper or 0.25 Isometric paper please.
Topics Discussed: Dynamics of Rigid Bodies, Rectilinear Motion, Rectilinear Kinematics, Erratic Motion, Curvilinear Motion, Rectangular Component of Rectilinear Motion Kindly show the complete solution. Please make sure that your handwriting is understandable and the picture of the problem is clear. I will rate you with “like/upvote” after. I need the answer right away, thank you.
-Draw the principal views on the left side of your drawing paper. Analyze the principal views and dimensions of the Lap Dovetailcarefully below. Construct the isometric view from the given views and details. -The object is symmetrical about its principal center lines.-The isometric view must be according to the dimensions as indicated.-Supply missing dimensions if necessary.
You are tasked with designing the runway on an aircraft carrier. The minimum speed for the F/A-18 Hornet is 193.8 mph. The Hornet weighs 40,000 lbf and its twin engines provide a thrust of ~40,000 lbf combined, providing a max acceleration of 1g. How long must the deck be to takeoff unassisted in feet?