The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 12 mm2. The cross-sectional area of rod (2) is 16 mm2. For a uniformly distributed load of w = 3.3 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 4.75 m. (1) (2) a L Answer: a = i

The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 12 mm2. The cross-sectional area of rod (2) is 16 mm2. For a uniformly distributed load of w = 3.3 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 4.75 m. (1) (2) a L Answer: a = i

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two solid cylindrical rods support a load of P = 25 kN as shown. Rod (1) has a diameter of 13 mm, and the diameter of rod (2) is 12 mm. Determine the axial stress in rod (1).
If the output torque on the CD shaft is T ́ = 75 N-m and the motor rotates at 175 rpm, determine the power delivered by the motor in watts. • Is there torque at the BE and CF ends? • Calculate the maximum shear stress in the AE axis.
NO. 4. The 150-kg bucket is suspended from end E of the frame. Determine the average normal stress in the 6- mm diameter wire CF and the 15-mm diameter short strut BD IN Figure 4.
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
The shaft shown in (Figure 1) is supported by bearings at A and B that exert force components only in the x and z directions on the shaft. If the allowable normal stress for the shaft is σ allow = 15 ksi, determine the smallest diameter of the shaft that will support the loading. Use the maximum shear stress theory of failure. Take τ allow = 2.7 ksi.
The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
For the beam in the question above, determine the maximum shear stress. sketch thesection stress distribution.
The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load P as shown. a. Determine the torsional shear stress at Point A (50mm from the center) and Point B (on the Surface) b. Determine the absolute maximum torsional shear stress in the shaft. c. sketch the state of stress at point A and draw its corresponding Mohr’s Circle of stress. compute the principal stresses and maximum in-plane stress. T=10.38kN-m
Question ) Forces of F1=3 kN from point B in the z direction, F2=5 kN from point C in the z direction and F3=8 kN in the y direction are acting on the arm in the figure. The lengths of the arm are also given as L1=0.18 m and L2=0.17 m. It is desired to determine the stress state of point A on the a-a section taken from the arm. The radius r of the section is r=0.3 m and the shear modulus of the arm material is G=79 Gpa. According to this; Question 1-A) Find the shear stress due to the shear force at point A. (Write your result in MPa.Question 2-B) Find the shear stress due to the torsional moment at point A. (Write your result in MPa.Question 3-C) Find the total shear stress at point A. (Write your result in MPa)Question 4-D) Find the normal stress caused by the normal force at point A. (Write your result in MPa Question 5-E) Find the normal stress caused by the bending moment at point A. (Write your result in MPa.)Question 6-F) Find the total normal stress at point A. (Write your…
A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to an axial tension load of P = 76 kN and torques TB = 15 kN-m and TC = 4 kN-m, which act in the directions shown. Determine the normal stress x at point H.
A thin walled tube of thickness (t) 5mm and diameter (d) 200mm with closed ends is subjected to an internal pressure (p) 7.0 MN/m2, producing an axial and circumferential direct stresses given by pd/4t and pd/2t respectively. A torque T = 15.0 kNm is also applied which sets up a shear stress ? = ?/2??2? where r is the radius. (a) Determine the magnitude and direction of the principal stresses. (b) Calculate the overall maximum shear stress.
Determine the average normal stress at section a-a and the average shear stress at section b-b in member AB. The cross-sectional is square, 0.55 in. On each side.