The sports car of center of mass at G a mass of 2 Mg shown in the figure below is traveling at a constant acceleration of ag = 1.59 m/s². Neglect the mass of the wheels. The coefficient of friction between the wheels and the road is = 0.25. If the engine of the car only drives the rear wheels, whereas the front wheels are free rolling, determine the normal reactions exerted road on the pairs of the wheels at A and at B. A-1.25 m+ 0.3 m B -0.75 m Select one: OA N₁-8.66 kN, and Ne 10.92 kN 2.7 kN OB NA 16.88 KN, and Ns OC NA 10.88 kN, and Ne 8.7 KN OD. NA 6.88 kN. and Ne = 12.7 KN

The sports car of center of mass at G a mass of 2 Mg shown in the figure below is traveling at a constant acceleration of ag = 1.59 m/s². Neglect the mass of the wheels. The coefficient of friction between the wheels and the road is = 0.25. If the engine of the car only drives the rear wheels, whereas the front wheels are free rolling, determine the normal reactions exerted road on the pairs of the wheels at A and at B. A-1.25 m+ 0.3 m B -0.75 m Select one: OA N₁-8.66 kN, and Ne 10.92 kN 2.7 kN OB NA 16.88 KN, and Ns OC NA 10.88 kN, and Ne 8.7 KN OD. NA 6.88 kN. and Ne = 12.7 KN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The velocity of the 8-kg cylinder is 0.3 m∕s at a certain instant. The speed v after dropping an additional 1.5 m is 2.5 m/s. The mass of the grooved drum is 12 kg, its centroidal radius of gyration is k = 210 mm, and the radius of its groove is ri = 200 mm. The frictional moment at O is a constant 3 N∙m. Find the frictional force.
If the speed of the shaft, as shown in Figure 1 below, is 220 rev/min, calculate the magnitudes and orientations of the bearing reactions at A and B for the two-mass system. Given a = b = 250 mm, c = 50 mm, R1 = 60 mm, R2 = 40 mm, m1 = 2 kg, and m2 = 1.5 kg.
In the figure, the hanging object has a mass of m1 = 0.420 kg; the sliding block has a mass of m2 = 0.850 kg, and the pulley is a hollow cylinder with a mass M = 0.350 kg, a interior radius R1 = 0.0200 m and an exterior radius R2 = 0.0300 m. Assume that the mass of the rays is negligible. The coefficient of kinetic friction between the block and the surface horizontal is µk = 0.250. The pulley rotates without friction on its axis. The lightweight cable does not stretch and does not slip on pulley. The block has a velocity of vi = 0.820 m / s towards the pulley when you pass a landmark on the table. (a) Use energetic methods to predict its velocity after it has passed a second point, which is at 0.700 m. (b) Find the angular speed of the pulley at the same moment.
The thin rod in the figure has a mass of 15kg and is attached to a spring of constant k = 50 N / m at one end, which has an unstretched length of 1.5 m. If the rod is released from rest in a horizontal position (ѳ = 0 °) and only conservative forces act on it, determine:a) What is the moment of inertia of the thin rod around the axis of rotation at A? b) What is the angle at which the rod is momentarily at rest again? c) What is the maximum angular velocity of the path?
The shown spool has a mass of 450 kg and aradius of gyration Gk=1.2 m. It rests on thesurface of conveyer belt for which the coefficient offriction m= 0.5. If the conveyer acceleratesat2 1.2m / S and the spools rolls without slipping,determine the tension in the wire and the angularacceleration of the spool
The motorcycle in the figure has a mass of m1 kg and its center of mass is at G1. The mass of the driver is m2 kg and the center of mass is at G2. Since there is fs between the wheels and the asphalt, determine whether it is possible for the driver to lift the front wheel off the ground. Neglect the mass of the wheels and assume that the front wheel can spin freely. a=0.41 m b= 0.39 m c= 0.75 m d= 0.25 m e=0.58 m m1=120 kg m2= 77 kg fs=0.82
3.32). As shown in Figure 3, a yo-yo toy is formed by wrapping a massless cord around adisk of radius R= 0.2 m and mass M=3 kg. The cord is vertical and its top end is fixed and the disk isinitially stationary. The cord remains vertical for the entire motion and does not slide on the disk.When the disk is released from rest, it falls down by a distance H=0.8 m, The moment of inertia ofthe disk around its center is I disk=1/2mdiskR^2a . Find the angular acceleration of the disk when it is lowered by a distance H.b . Find the angular velocity of the disk when it is lowered by a distance H.
The double pulley shown in the figure is formed by two wheels that are coupled to each other. The complete pulley (formed by the two wheels) has a mass of 15 kg and a turning radius of 110mm. Block A has a mass of 40 kg. If a force of 2 kN is applied to the tied rope of the inner pulley wheel, determine the speed of block A after 3 seconds. At the beginning, the whole system was at rest. Disregard the mass of the string and consider that the moment of inertia (kg.m²) of the complete pulley is given by IP = mko²where m is the mass of the pulley and Ko is the radiusspinning
In the figure, the slender bar (1), with a mass of 30 kg, is attached to the sphere (2), with a mass of 80 kg. Given the angular velocity shown at the provided angle, determine: a. The angular acceleration of the combined body b. The reactions in the pin at point O
The slender, homogeneous rod shown in the figure below is 3 m in length and has a mass of 12 kg. At the instant shown, the rod has an angle to the horizontal of 60-degrees and an angular velocity of 2 rad/s clockwise. Both walls are smooth and provide negligible friction. At the instant shown, what are the reaction forces at A and B? What is the angular acceleration of the rod's center of mass?
The wheel in the figure has a mass of 40 kg and a radius of rotation, in relation to its center of gravity, kG = 250 mm. Whereas there is no slip, determine the work done by the weight after it rotates 90 ° clockwise from illustrated position. The AB spring has a constant stiffness k = 100 N / m and a length in the undisturbed situation of 500 mm. Consider that the wheel is initially at rest.
The right‐angle plate is formed from a flat plate having a mass ρ per unit area and is welded to the horizontal shaft mounted in the bearing at O. If the shaft is free to rotate, determine the initial angular acceleration α of the plate when it is released from rest with the upper surface in the horizontal plane. Also determine the y‐ and z‐components of the resultant force on the shaft at O.