The static wave ratio in a 300 ( 2) lossless transmission line terminating at an unknown load impedance is 2.0, and the nearest minimum voltage is 0.31 from the load. A)Reflection coefficient r times Find that the input impedance is equal to ZL. B)Unknown load impedance Z1 Find that the input impedance is equal to Z. C) Equivalent length and line termination resistance Find that the input impedance is equal to ZL.

The static wave ratio in a 300 ( 2) lossless transmission line terminating at an unknown load impedance is 2.0, and the nearest minimum voltage is 0.31 from the load. A)Reflection coefficient r times Find that the input impedance is equal to ZL. B)Unknown load impedance Z1 Find that the input impedance is equal to Z. C) Equivalent length and line termination resistance Find that the input impedance is equal to ZL.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.31P: A 500-kV, 300-km, 6()-Hz, three-phase overhead transmission line, assumed to be lossless, has a...

See similar textbooks

Similar questions

A 50Ω lossless transmission line is terminated with a load impedance valued ZL = RL + jXL.According to what is given, a) RL for Voltage Standing Wave Ratio to be 2What should be the relationship between XL and?b) If RL = 100Ω, find the value of XL.c) Find the voltage minimum point closest to the load on the line.
1. What is the necessary condition for matching transmission lines? In addition, what is a micro strip line? 2. For a distortion less line α = 0.02dB/m, Z0 (R0) = 60Ω and C = 0.2nF/m. Find the resistance and velocity of wave propagation. [Do not forget the units.] 3. For a finite lossless transmission line with open-circuit termination, sketch Xio vs l. Indicate where the sketch is inductive and capacitive.
The capacitance per unit length and the characteristic impedance of a lossless Transmission line are C and Z0 respectively. Express the velocity of travelling wave on the transmission line in terms of the two given parameters above.
A lossless transmission line has 100 ? characteristic impedance. The line is terminated in a load impedance of 70-j100 ?. The maximum voltage measured on the line is 200V. Find;1. The minimum current and minimum voltage on the line2. Explain how location of voltage maximum can be determined by using load reflection coefficient from the forward and backward wave.3. Using load reflection coefficient in ii., calculate the distance from the load that produce the maximum voltage and current.
A 300ᘯ transmission line is 0.8 m long and terminated with ashort circuit. The line is operating in air with a wavelength of 0.8m and is lossless. (a) If input voltage is 10V, what is themaximum voltage amplitude at any point on the line? (b) Whatis the current amplitude in the short circuit?
An extra high voltage transmission line of length 300 km can be approximated by a lossless line having propgation constant is 0.00127 rad/km. The percentage ratio of line length to wave length will nearly by ?
Estimate the characteristic impedance and propagation constant of a lossless transmission line in terms of the transmission line parameters (Resistance per unit length etc.).
An extra high voltage transmission line of length 300 km can be approximate by a lossless line having propogation constant β= 0.00127 radians per km. Then the percentage ratio of line length to wavelength will be given by ??
The capacitance per unit length and the inductance per unit length for a lossless transmission line are 0.1 F/m and 20 H/m respectively. What will be the characteristic impedance of the line?
. A 70 cm long lossless transmission line with characteristics impedance of 50 Ω operating at 5Mhz is terminated with a load of ?? = (65+j80) Ω. If the velocity is 0.8 times the velocity of light, then calculate (a) The reflection co-efficient, also verify the value using the given smith chart. (b) Compute the input impedance using the transmission line input impedance equation 50 Ω line is terminated with an impedance of ??= (90 – j120) Ω. Design a shortcircuited single stub matching circuit using Smith chart that is provided
Derive an expression for sag in a transmission line of equal height poles
A 50-ohm lossless transmission line is terminated by a 100-ohm resistive load and is operated at 100 MHz. At an electrical length of 0.8 wavelengths, what is input admittance?