Answered: For the plane trusses shown in Figure…

For the plane trusses shown in Figure P3-30, determine the horizontal and vertical displacements of node 1 and the stresses in each element. All elements have E = 210 GPa and A = 4.0 x 10-4 m2.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.12P: - 7.3-12 A simply supported beam is subjected to two point loads as shown in the figure. The...

See similar textbooks

Related questions

Q: 3 For the plane trusses supported by the spring at node 1 in Figure P3–33 (a) and (b), determine the…

Q: "Prob. 3.3-10. A 12-ft beam AB that weighs W, 180 lb supports an air conditioner that weighs W, =…

A: Given that: Length of the beam = 12 ft = 144 in Wa = 1000 lb, Wb = 180 lb It is required to…

Q: The stresses acting on element A in the web of atrain rail are found to be 40 MPa tension in the…

A: Given Stress = 40 MPa tension = 160 MPa compression Shear stress = 54 MPa Find…

Q: The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between…

Q: Problem 1 of 2: Nodal displacements for the elements 1-3 and 2-3 of a plane truss were determined to…

A: Given dataDisplacements of points in x and y directionsu1 = 1.5mmu2 = 0.2mmu3 = -2.7mmv1 = 3.1mmv2…

Q: Determine the nominal block shear strength of the tension member shown in Figure P3.5-2. The bolts…

A: Write the expression for shear areas and substitute the values from the given figure.

Q: Find the normal stress and shear stress in the c-plane for the stressed member shown in the figure.…

A: Given figure To determine the normal stress and shear stress in the c-plane for the stressed…

Q: For the plane trusses shown in Figures P3-29 and P3-30, determine the horizontal and vertical…

Q: For the disc saw shown in the figure below a key is used to transfer a torque of 20 Nm. Calculate…

Q: 3.40-3.41 For the space trusses shown in Figures P3-40 and P3-41, determine the nodal dis-…

Q: The T-section short column shown in Figure 2 carries an eccentric load P of 100 kN at the position…

Q: mple 4.3 (Numerical problem on thick cylinder subjected to internal urel: A thick cylinder of…

A: Answer: The thickness required of thick cylinder is 20.71 mm.

Q: For the structure shown in the figure, the working stresses are up to 16000 psi for the steel cable…

Q: Problem 6.4: Each member of the truss in Figure (6.21) is a solid circular rod with diameter d=10…

Q: 2.10-3 A flat bar of width b and thickness 1 has a hole of diameter d drilled through it (see…

A: Given data: - The width of the bar is b. The thickness of the bar is t. The diameter of the hole…

Q: For the stress state shown in the figure; Using Mohr's circle calculate: a) Principal stresses…

A: Given data and Initial Calculation:-

Q: Q4-A shaft (55 mm) diameter is transmit power of 200 W at 1200 rpm, the maximum shear stress of (80…

A: Given data: - The diameter of the shaft is d = 55 mm. The power transmit is P = 200 W. The speed of…

Q: For the structure shown in Figure P15-5, bar element 1 is subjected to a uniform temperature rise of…

A: Given: TO determine: Stress in each bar

Q: 3.33 For the plane trusses supported by the spring at node 1 in Figure P3-33 (a) and (b), determine…

A: As per our guidelines, we are supposed to answer only one question. Kindly repost other question as…

Q: B5

A: Given Data :- angle is threta radius is r

Q: For the voltage state shown in the figure; Using Mohr's circle, calculate: a) Principal stresses and…

A: Given Data:- σx=300lb/pulg2ζxy=120lb/pulg2

Q: The stresses at a point on the surface of a generator shaft are ox = -50 MPa, ơy = 30 MPa and Txy =…

Q: For the assembly shown in Figure.(5). If the stress in the steel rod become (170) Mpa when the…

Q: For the plane trusses with inclined supports shown in Figure P3-51, solve for the nodal…

Q: The cantilevered bar in the figure is made from a ductile material and is statically loaded with Fy…

Q: An aluminium stepped shaft is rigidly fixed at the wall and has been loaded with concentrated forces…

Q: Figure Q5 shows a thick cylinder of 50 mm internal radius and 130 mm outer radius is subjected to an…

A: 2 Given: The internal radius, ri = 50 mm The outer radius, ro = 130 mm The internal pressure, Pi =…

Q: Problem 4. The structure in the figure is composed of two rigid bars (AB and CD) and two vertical…

A: The free-body diagram of the beam is as shown below, Assumption: Let the length of aluminum and…

Q: 3-67: A short post is made by welding steel plates into a square. as shown in Figure P3-67, and then…

A: Given data as per question b = 1500 mm t = 10mm axial load = 900 kN f'c = 6000 psi = 41.37 N/mm2…

Q: The solid bar shown in the figure has a radius of 0.75 in. Determine the state of stress at point A…

Q: -10 A rigid bar rests on aluminum-alloy and steel uprights, as shown in the figure.( a) Determine…

Q: A portion of the stress-strain curve for a stainless steel alloy is shown in Figure Q-2. A 350 mm…

A: Write the expression of the normal strain.

Q: For Problems 64 through 68, compute the maximum stress in the member, considering stress…

A: Given data: - The minimum width of the plate is d = 0.80 in. The maximum width of the plate is D =…

Q: following : 5.1.The maximum compressive

Q: Problem 8-12 A bar of rectangular cross-section, with a width of 60 mm and a thickness of 40 mm, is…

Q: Question 3 - Torsion ( A composite shaft is shown in the figure below which is fixed against…

Q: Problem 2.3 A machine bracket is loaded with an inclined force of 1000 N as shown in the figure…

Q: A cable and pulley system at D is used tobring a 230-kg pole (ACB) to a vertical position, asshown…

A: Draw a diagram for the problem. Here, W is the weight of the pole, T is the tension in the cable,…

Q: Compute the total elongation of the bar shown in Figure P3-37 if it is made from titanium 3-37.…

A: Reaction at A; Axial loading diagram: Now,

Q: Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm…

A: Stress (σ) is defined the force per unit area.

Q: 140mm 450 mm 100 mm | I kN In the figure, a force of 1 kN is applied by means of an arm connected to…

Q: The cantilevered bar in the figure is made from a ductile material and is statically loaded with Fy…

Q: The recessed composite beam in the figure is made of steel and aluminum It was produced and a force…

A: Given dataApplied point load P = 20kNLength of the beam L = 2mYoungus modulus of steel Est =…

Q: 3-65: A stainless steel (SAE 301) wire is stretched between rigid supports so that a stress of 40…

A: Given data as per question Stress at supports = 40Mpa Temperature of the wire = 200 C Final…

Q: a) Draw Mohr's circle for this element, clearly showing the locations and values of the stresses in…

Q: The stresses at a point on the surface of a generator shaft are o =-50 MPa, o, = shown in Figure Q3.…

Concept explainers

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.

Question

For the plane trusses shown in Figure P3-30,
determine the horizontal and vertical displacements
of node 1 and the stresses in each element. All
elements have E = 210 GPa and A = 4.0 x 10-4 m2.
Sm
80 AN
Figure P3-30

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An element in plane stress is subjected to stresses sx= -5500 psi, sy= -2000 psi, and Tx. = 1900 psi (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A simply supported wood beam is subjected to point load P at mid-span. The stresses on element C are known to be ??x=-92 psi and txy= -7 psi. Find the principal stresses on the element and show them on a sketch of a properly oriented clement.
A double-decker bicycle rack made up of square steel tubing is fixed at A (figure a). The weight of a bicycle is represented as a point load applied at B on a plane frame model of the rack (figure b). (a)Find the state of plane stress on an element C located on the surface at the left side of the vertical tube at the base A. Include the weight of the framing system. (Assume weight density y = 77 kN/m .) (b) Find the maximum shear stresses on an element at C and show them on a sketch of a properly oriented element. Assume that element C is a sufficient distance from support A so that stress concentration effects are negligible
A solid aluminum bar (G = 27 GPa ) of diameter d = 40 mm is subjected to torques T = 300 N - m acting in the directions shown in the figure, Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A cylindrical tank with hemispherical heads is constructed of steel sections that are welded circumferentially (see figure). The tank diameter is 1.25 m, the wall thickness is 22 mm, and the internal pressure is 1750 kPa, (a) Determine the maximum tensile stress h in the heads of the tank. (b) Determine the maximum tensile stress c in the cylindrical part of the tank. (c) Determine the tensile stress <7W acting perpendicular to the welded joints, (d) Determine the maximum shear stress rtiin the heads of the tank. (e) Determine the maximum shear stress tcin the cylindrical part of the tank
A steel bar with a diameter d = 12 mm is subjected to a tensile load P = 9.5 kN (see figure). (a) What is the maximum normal stresser smax in the bar? (b) What is the maximum shear stress tmax? (c) Draw a stress element oriented at 45° to the axis of the bar and show all stresses acting on the faces of this element. (d) Repeat part (c) for a stress element oriented at 22.5° to the axis of the bar.
A traffic light and signal pole is subjected to the weight of each traffic signal We = 45 lb and the weight of the road lamp WL= 55 lb. The pole is fixed at the base. Find the principal normal stresses and the maximum shear stress on element B located 19 ft above the base (see figure). Assume that the weight of the pole and lateral arms is included in the signal and lamp weights
A steel hanger bracket ABCD has a solid, circular cross section with a diameter of d = 2 in. The dimension variable is b = 6 in. (see figure). Load P = 1200 lb is applied at D along a line DIh the coordinates of point H arc (8/>, — 5b, 2b), Find normal and shear stresses on a plane stress element on the surface of the bracket at A. Then find the principal stresses and maximum shear stress. Show each stress state on properly rotated elements
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A circle of a diameter d = 200 mm is etched on a brass plate (see figure). The plate has dimensions of 400 x 400 x 20 mm. Forces are applied to the plate, producing uniformly distributed normal stressescr^ =59 MPaander^ = —17 MPa. Calculate the following quantities: (a) the change in length Aac of diameter at: (b) the change in length Abd of diameter bd; (c) the change At in the thickness of the plate; (d) the change AV in the volume of the plate; (e) the strain energy U stored in the plate; (f) the maximum permissible thickness of the plate when strain energy £/must be at least 784 J; and (g) the maximum permissible value of normal stress axwhen the change in volume of the plate cannot exceed 0.015% of the original volume. (Assume E = 100 GPa and v = 0.34
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.