The structure shown below carries a load of 20 kN. Determine the required diameters of rods AE and AB if the allowable stress in the rods is 130 MPa. Using the largest rod diameter in your computation, estimate the elongation of the rods. Also, determine the required diameters of the pins at F and C if the allowable shear stress is 110 MPa. Load 375 E 1800- Dimensions in mm Boom 1650 F 600 900

The structure shown below carries a load of 20 kN. Determine the required diameters of rods AE and AB if the allowable stress in the rods is 130 MPa. Using the largest rod diameter in your computation, estimate the elongation of the rods. Also, determine the required diameters of the pins at F and C if the allowable shear stress is 110 MPa. Load 375 E 1800- Dimensions in mm Boom 1650 F 600 900

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please give neat and proper step by step solution. A tie rod of uniform section is required to resist a force of 450 kN at an eccentricity of 25 mm from the axis of the rod. Determine the size of the tie rod if the permissible stress is limited to 125 N/mm².
What wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of 18 MPa? Use a design stress of 80 MPa?
A rod is hanging vertically, supports a load of 2000N. Neglecting the weight of the wire, determine the required diameter if the tensile stress is 140MPa.
As shown in Fig., a 10ft rigid beam with negligible weight is pinned at one end and attached to two vertical rods. The beam was initially horizontal before the load W = 63 kips was applied. Find the vertical movement of W.
A uniform concrete slab of mass M is to be attached to two rods whose lower ends arw initially at the same level. find: The area of aluminium bar so that slab will remain level after it is attached to the rods. The stress in the steel rod if M=18000kg The stress in aluminum rod if M=18000kg The elongation of the streel rod The elongation of the aluminum rod.
A rope has a cross sectional area of 0.002m2 and is being used to lift a 5000N weight. What is the stress in the rope?
A U-bolt supports a load of 5,000 lb. The cross-section of the bolt has a diameter of ½ in. How much stress is induced in the sides of the bolt? note: answer must be in ksi
Q // If the value of the highest load we get from the tensile test of a wrought iron model with a circular . section is (52 kN) with an axial stress of ( 460 Mpa), calculate the diameter of the examined model
A 2-in.-diameter round steel rod 10 ft long is subjected toa tensile force of 60 kips. How much will it elongate under the load?
A mild steel rod of 15mm diameter that is 1.5.m in length is elongated by 0.15cm along its longitudinal direction by a load of 15 kN. The intensity of stress is?
Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane as shown in Fig.1 Initially, all the rods are adjusted to share the load equally. Neglecting any chance of buckling, and taking Esteel= 205 GPa and Ecopper 100 GPa, determine the initial and final stresses when a further load of 20 kN is added.
The suspender rod is supported at its end by a fixed-connected circular diskas shown in Fig. 1–26a. If the rod passes through a 40-mm-diameter hole,determine the minimum required diameter of the rod and the minimumthickness of the disk needed to support the 20-kN load. The allowablenormal stress for the rod is sallow = 60 MPa, and the allowable shear stressfor the disk is tallow = 35 MPa.