The structure supports a distributed load of w. The limiting stress in rod (1) is 400 MPa, and the limiting stress in each pin is 210 MPa. If the minimum factor of safety for the structure is 2.40, determine the maximum distributed load magnitude w that may be applied to the structure plus the stresses in the rod and pins at the maximum w. 2.1 m 16-mm-diam. pin double shear 18-mm-diam. rod w (kN/m) 4.3 m (1) 01 (MPa) single shear 20-mm-diam. pin 6.6 m Тв (MPa) A Ic (MPa)

The structure supports a distributed load of w. The limiting stress in rod (1) is 400 MPa, and the limiting stress in each pin is 210 MPa. If the minimum factor of safety for the structure is 2.40, determine the maximum distributed load magnitude w that may be applied to the structure plus the stresses in the rod and pins at the maximum w. 2.1 m 16-mm-diam. pin double shear 18-mm-diam. rod w (kN/m) 4.3 m (1) 01 (MPa) single shear 20-mm-diam. pin 6.6 m Тв (MPa) A Ic (MPa)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The steel bracket below is used to connect the ends of two cables. If the applied force P=1.50kip, determine the maximum normal stress (in ksi) in the bracket. Assume the bracket is made from a rod having a diameter 1.5in.
A steel pipe with an outer diameter of 50 mm and a wall thickness of 5 mm is subjected to aninternal pressure of 10 MPa and an axial load of 20 kN at an angle of 45 degrees to the axis of thepipe. Determine the maximum axial stress and maximum hoop stress developed in the pipe.
. The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B . If P = 5 kN and the shaft is made from steel having an allowable normal stress of sallow = 150 MPa and an allowable shear stress of tallow = 85 MPa, determine the required minimum wall thickness t of the shaft to the nearest millimeter to safely support the load.
The five-bolt connection must support an applied load of P = 1800 lb. If the average shear stress in the bolts must be limited to 47 ksi, determine the minimum bolt diameter that may be used for this connection.
A 150-mm-long bronze tube, closed at its ends, is 80 mm in diameter and has a wall thickness of 3mm. it fits without clearance in an 80-mm hole in a rigid block. The tube is then subjected to an internal pressure of 4.00 MPa. Assuming v=1/3 and E= 83 GPa, determine the tangential stress in the tube.
The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3,080 mm^2. The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C.
The steel bracket is used to connect the ends of two cables. If the allowable normal stress for the steel is sallow = 30 ksi, determine the largest tensile force P that can be applied to the cables. Assume the bracket is a rod havinga diameter of 1.5 in.
The rigid bar of negligible weight is supported as shown. The middle helical spring is made of 22 mm diameter steel spring and has an outside diameter of 100 mm with 10 turns and the two side springs are made of 32 mm steel spring and has an outside diameter of 250 mm with 8 turns. Before the load P is applied, the side springs are 25 mm longer than the middle spring. If the applied load P = 15 kN and the rigid bar remains horizontal, determine the stress in each spring. Use G = 83 GPa for steel and G = 42 GPa for bronze.
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 12 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 95 MPa, and the bearing stress between the rod head and the support plate cannot exceed 135 MPa. Determine the maximum value of Pmax that can be supported by the structure.
A.) If the F = { - 200i + 400j } N , determine the force in each member and state if its in compressions or tension. A.) Using the same given, if the members have a square cross-section with a diagonal of 11.31cm and thickness of 1cm, determine the axial stressess and the factors of safety on each of the member, if the maximum allowable tensile strength is 60kPa and the maximum allowable compressive strength is 70kPa NOTE: Complete solution and units, free body diagrams, table data if possible <up voting!>