Given: Otto Cycle with the following data:compression ratio = 9intake air is at 100 KPa and 20°Cmaximum cylinder volume = 500 cm³Temperature at the end of adiabatic compression = 800 KCp =1.01 kJ/kgK, Cv=0.718 kJ/kg, k = 1.4, R = 287.1 J/kgK the temperature T3 in K is nearly equal toO 2035O 19731926O 1856

Answered: Image /qna-images/answer/d399bbcf-b747-49be-83ad-7047d557620b.jpg

Answered: the temperature T3 in K is nearly equal…

Engineering

Mechanical Engineering

the temperature T3 in K is nearly equal to

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A refrigerator used to cool a computer requires 1.2 kW of electrical power and has a COP of 1.8.…

A: Electrical power input = Power required to run compressor = Work input = 1.2 kW COP of the…

Q: From the overall free-body diagram for the engine (below), the value of the moment M, is kN-m.

Q: Water at 20◦C flows along the streamlines shown in Figure 3.11. The (gauge) pressure, velocity, and…

A: Given Pressure, P1 = 15 kPa Velocity, v1 = 1 m/s v2 = 0.5 m/s Elevation, z1 =…

Q: How far is the starting of space from earth surface? What is the difference between rocket and…

A: To find: Distance between starting point of space and Earth's surface. Difference between rocket and…

Q: A vertical bar of length L with mass of 40 kg is rotated vertically about its one end at 40 rpm.…

A: Answer: The length of the bar is 1.58 m.

Q: Superheated steam at 652 psia and 608 F is generated in an Oil-fired boiler at the rate of 100,000…

A: Write the enthalpy of the superheated steam. hg=1290.72 Btu/lb Write the enthalpy of the feed water.…

Q: The wheel is made from a 5-kg thin ring and two 2-kg slender rods. If the torsional spring attached…

Q: If e=26.3°, calculate the minimum coefficient of static friction at A and B so that the frame's…

Q: H.w (1) A refrigerator used to cool a computer requires 1.2 kW of electrical power and has a COP of…

Q: emperature by 60 degrees Celsius. Calculate the stresses in copper and steel before and after the…

A: Diameter=drod=12mmLcopper…

Q: What is the acceleration of the body that increases in velocity from 20 m/s to 40 m/s in 3 seconds?…

Q: A 1 mm thick cylindrical tube, 100 mm in diameter, is orthogonally turned such that the entire wall…

Q: The second law of thermodynamics implies that the coefficient of performance of a refrigerator must…

Q: A steel flask of 0.06 m³ capacity is to be used to store nitrogen at 140 bar, 20° C.The flask is to…

A: Given:P1=140 barT1=20 CV1=0.06 m3

Q: novel heat engine is being considered for producing work from the thermal energy contained in the…

Q: 4.19 and 4.20 Knowing that for the extruded beam shown the allowable stress is 120 MPa in tension…

Q: 15. Suppose energy is continuously transferred as heat at constant pressure to a solid till it is…

Q: 10-6. The solid 30-mm-diameter shaft is used to transmit the torques applied to the gears. Determine…

Q: The simply supported beam is used to supports loads and moment as shown below. Draw shear and moment…

Q: A furnace wall is to consist in series of 7 in of kaolin firebrick, 6 in of kaolin insulating brick,…

A: In thermodynamics the transfer of the molecules from the one high temperature body to the lower…

Q: 9.5 (a) How are the loss coefficients for stationary and moving rows of blades in a turbine stage…

Q: 3- The following rod rotates about AB axis. If the angular velocity and acceleration are…

Q: Determine the moment of inertia of the shaded area with respect to the x and y axis as shown in…

A: Draw the diagram of shaded area.

Q: F2-13. Determine its coordinate direction angles of the force. F=75 lb

A: We can answer the first question since the exact one is not specified. Please resubmit the question…

Q: Calculate the stress of the cylindrical rod. Compare with data given in Table Q1 which are the…

A: we have to calculate the stress

Q: As you are walking in the forest you look up just as a boulder becomes dislodged from the side of a…

A: Height of the boulder from the head, h= 200 ft Acceleration due to gravity, a= 32 ft/sec2 Initial…

Q: wo bodies of masses (m₁ = 7 kg) and (m₂ = 5 kg) are connected by a light string passing over a…

Q: 7ft Corce докл 66° 5.30 look 50 g 80° G 36 30 Yo >15 4ft 3ff for all member f 66 2ft ? E

Q: the square lamina A B C D is placed Parallel to the H.P. and having the following (Q data A (2, 2),…

A: A=2,2D=2,7Projector distance between A and D=4Auxiliar plane perpendicular to V.P. and H.P.

Q: The Mohr's circle representing a given state of stress is shown. The diagonal line AB represents the…

A: Given

Q: Given the following: gas = ideal m = 1,360 g R = 0.377 kJ/kg-K k = 1.25 P₁ = 551,600 Pa T₁ = 333.15…

Q: .1/A Rs) Determine the magnitude of the component force F in Fig. and the magnitude of the resultant…

Q: A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of…

Q: A band brake embraces a 500 mm diameter drum with an angle of lap of 270° and produces a braking…

Q: When a0, the spring on the firing mechanism is unstretched. The arm is pulled back such that 100 mm…

Q: Convert the reading of pressure to kpa.

Q: A non-uniform bar rests across two supports that are 20 ft apart. When loads of 200 lb, 4 ft from…

A: The weight of the bar is 80 lb and the position of the center of gravity is 13 ft from A.

Q: Give the PV and TS Diagrams of Binary Cycle system Give its Formula for Thermal Efficiency. Give…

Q: Q. 2 (b) A rectangular plate 0.6 m wide and 1.2 m deep lies within a water body such that its plane…

A: Here, Area of plate, A=0.6×1.2=0.72 m2 Distance of centroid G from free surface,…

Q: A railway car wheel rolls on a rail. Both rail and wheel are made of steel for which E = 210 GPa and…

A: A train car wheel is rolling on a rail.Steel with E=210 GPa and v=0.3 is used for both the rail and…

Q: Q.1/A Rs) Determine the magnitude of the component force F in Fig. and the magnitude of the…

Q: The farmer wanted to know the number of hills per hectare in his rice production, if row is 15 cm…

A: Givenw=15cmb=15cm

Q: a projectile is fired from the origin at t 0 with a positive v component, the maximum Hight h can be…

Q: 2. The force F-(2x-yja, + (x+y+zja, +(22-xja, [Newtons] is given. Calculate the total work required…

A: Given data Force is given byF = 2x-y ax + x+y+z ay + 2z - x az NWe have to calculate the total…

Q: An ideal gas whose R = 25.8 ft-lbf/lbm-R and k = 1.09 was cooled from 636 R to 565 R at constant…

A: T1 = 636 R T2 = 565 R R = 25.8 ft-lbf/lbm-R k = 1.09

Q: Discuss size reduction machineries

A: Machines that crush and grind materials to reduce their size are known as size reduction…

Q: Given: Otto Cycle with the following data: compression ratio = 9 intake air is at 100 KPa and 20°C…

Q: The product structure diagram shows the number of different components required at each level to…

A: The number of additional units of component A needed to produce 10 units of product P is 110 units.…

Q: Find the value of each of the angles β and α that keep the system of forces in equilibrium

Q: a) The power screw in the arm engages the slider B and controls its distance from O according to r =…

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

Given: Otto Cycle with the following data:
compression ratio = 9
intake air is at 100 KPa and 20°C
maximum cylinder volume = 500 cm³
Temperature at the end of adiabatic compression = 800 K
Cp =1.01 kJ/kgK, Cv=0.718 kJ/kg, k = 1.4, R = 287.1 J/kgK

the temperature T3 in K is nearly equal to
O 2035
O 1973
1926
O 1856

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Final solution

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

an otto cycle operating in an air standard conditions has a peak tempearture of 800C. If the heat added in each cycle is equal to 350kj/kg. Determine the compression ratio of the cycle
The compression ratio of an Otto cycle working under air standard conditions is 8.0. Determine the peak temperature of the cycle if the heat supplied on the cycle is 3500kJ/kg of working ingredient.
A petrol engine with compression ratio of 15:1 was analysed as an air-standard cycle. The inlet pressure and temperature of the air are 101 kPa and 15 0C respectively while the maximum temperature of the cycle is 1,344 0C. The mass flow rate of air through the engine is 615 kg/min when running at its optimum speed. Thake the specific heat capacites at constant pressure as 1.0038 and 0.714 kJ/kgK. Calculate the thermal efficiency of the cycle power obtainable from the cycle
9. At the start of the compression process for of single cylinder cold air standard Otto cycle the pressure and temperature are P₁ = 100 kPa and T₁-300 K. If the compression ratio for this engine is equal to 10 and the net work produced by the engine is 500 kJ/kg, the mean effective pressure is most nearly equal to A. 301 kPa B. 350 kPa C. 645 kPa D. 666 kPa E. 5000 kPa
An air-standard Diesel cycle has a maximum temperature of 1800 K. At the beginning of compression, p1 = 95 kPa and Tq = 300 K. The mass of airis 12 g. For a compression ratio of 15, determine (a) the net work of the cycle, in kJ. (b) the thermal efficiency. (c) the mean effective pressure, in kPa.
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 2050 K. 1.)Determine the mean effective pressure, in kPa.
At the beginning of the compression process of air-standard Diesel cycle operating with a compression ratio of 18, the temperature is 300 K and the pressure is 0.1 MPa. The cut-off ratio for the cycle is 2 and the mass flow rate in the system is 1900 kg/hr. Cp=1.006 kJ/kg K Cv= 0.717 kJ/kg K 1) calculate the thermal efficiency of the cycle in %? 2) which formula should be used to determine the thermal efficiency of the cycle ?
The compression ratio of an air-standard Otto cycle is 7.5. P1 = 85 kPa and T1 = 32 Celsius at the startof compression. The highest temperature in the cycle is 960 K, and the mass of air is 3 g. determine the: (a) the heat rejection, in kJ, (b) the network, in kJ (c) the thermal efficiency, and the (d) mean effective pressure, in kPa. Show complete solution.
An air-standard Diesel cycle has a maximum temperature of 1800 K. At the beginning of compression, pq =95 kPa and T1 = 300 K. The mass of air is 12 g. For a compression ratio of 15, determine (a) the net work of the cycle, in KkJ. (b) the thermal efficiency. (c) the mean effective pressure, in kPa.
The compression ratio of an air-standard dual cycle is 12, and the pressure at the beginning of compression is 14.7 psia, the volume is 75 in3, and the temperature is 100 F. During the heat-addition processes, 0.4 Btu is transferred at constant volume and 1.0 Btu at constant pressure. Determine: (a) the cycle thermal efficiency (b) the pressure at the beginning of heat rejection.
An ideal Diesel engine operates on 1.5 lb of air with a suction state at 14.1 psia and 100 F. The pressure at the end of compression is 475 psia and the cut-off is 6% of the stroke from head-end dead - center. Using air properties (R-53.34 ft-lbf/lbm-R, k-1.4, Cp 24, Cvs. 1714 Btu/lbm-R), determine compression ratio, percentage clearance, Qa, Qr, Thermal Efficiency, mean effective pressure.
An air-standard Otto cycle uses 0.1 kg of air and has a clearance of 17%. The intake conditions are 98 kPa and 37°C, and the energy release during combustion is 1,600 kJ per kg. Determine the compression ratio.