The two metallic strips that constitute some thermostats must differ in:   A) length   B) thickness   C) mass   D) coefficient of linear expansion    E) rate at which they conduct heat

Q: An uncontrolled 850 kg car strikes squarely a motorway crash cushion in which the car is brought to…

A: we will use work energy theorem to solve this question  a all the kinetic energy of the car will be…

Q: Based on Figure Q10, the LOWEST toughness belongs to

A: Toughness is the ability of the material to withstand shock load. And toughness is…

Q: An uncontrolled 850 kg car strikes squarely a motorway crash cushion in which the car is brought to…

A: Given, Mass of the car = m = 850 kg Length of the crash cushion = L = 4.6 m Force required to crush…

Q: According to the U.S. Geological survey, the volume of water in oceans, seas, and bays is 1.41 ✕…

A: INTRODUCTION : The U-235 atom has 92 protons and 143 neutrons in its nucleus. When a U-235 atom's…

Q: Consider a closed piston cylinder that contains 0.2 kg of superheated water vapor at 200C and…

A:

Q: Wa B FIG. P4.4

A:

Q: A composite pendulum is made of a uniform slender rod and a uniform disk. If the rod has length of…

A: Find the mass moment of inertia about axis x' that pass through point O.

Q: A load of P = 6,100 N acts on the machine part shown. The machine part has a uniform thickness of…

A:

Q: Q2/ Determine the forces at the pin joint (F) and the roller support (G) ? 20 KN 30KN 2m By 2m D 2m…

A:

Q: A glass capillary tube of diameter 0.3 mm and length 60 mm is dipped in a water having surface…

A: Given datadiameter of capillary tube = d = 0.3 mm = 0.3 x 10-3 mLength of capillary tube = L= 60 mm…

Q: Critical point B 218 atm Water - Vapour Ice pressure curve 1.0 atm Water Triple point 4.58 vapour mm…

A:

Q: View Policies Current Attempt in Progress A typical stainless steel cylindrical vessel is shown. The…

A: Given data D = 48 in t = 0.75 in P = 1.1 ksi Find Hoop stress = ?

Q: Determine the coordinates of the centroid of the shaded area shown. Also, determine the volume of…

A: Given: To Find: 1. Coordinate of centroid. 2. Surface area 3. Volume

Q: Calculate the frictional power of an engine if the indicated power is 10 watts and the brake power…

A:

Q: Determine the coordinates of the centroid of the area that lies tween ne straight line x =2y/3 and…

A:

Q: b) Consider steady-state conditions for one-dimensional conduction in a plane wall having a thermal…

A:

Q: In the situation illustrated in the figure below, a small package is deposited by a conveyor belt at…

A:

Q: 41. The cross-section of the turbine rotor disc is de- igned for uniform strength under rotation…

A: Given          Density = 7470 kg/m3 Design stress = 250 MN/m2   Diameter, d = 60 mm       Speed, N =…

Q: Problem 8.5 A circular ring is subjected to a pull of 15 kN. The ring is of T-section as shown in…

A: A circular ring is known to be exposed to a 15 kN pull.The ring has a T-section, and the internal…

Q: ssion below, This expression is solvable by the method of inversion, if AX=B, A- coefficient matrix…

A: Option c is correct. A is non singular.

Q: Explain the long-term impact of saltwater on the pipeline. How might this influence material…

A: salt by nature is corrosive.

Q: A ring made of 25 mm diameter steel bar carries a pull of 10 kN 10 kN. Calculate the maximum tensile…

A: We know that a ring composed of steel bar with a diameter of 25 mm has a draw of 10 kN. We know the…

Q: m diameter is fixed fre m and 2 m from the natural frequency of shaf ig 11 CNm2

A:

Q: Explain the conditions for gravity wave existence and vertical propagation. Define the Froude number…

A: A gravitational wave is an invisible wave .these waves travel at the speed of light. these waves…

Q: REVISION HSTORY DATE NOTES: 140mm 180mm 16mm 1 20mm R18mm RIomm- 164mm -20mm 10mm PARTS LIST INIT…

A: It is given that all the dimensions are shown in top view and front view. So by helping these…

Q: orm of governing equations are solved at the grid points to find the unknown fluid quantitie

A: Grid generation in CFD is a collection of techniques for defining a numerical mesh throughout the…

Q: Q3:the shaded area shown in the figure find Moment of Inertia With respect to the X-axis

A: To find Moment of inertia W.r.t x-axis

Q: Using nodal analysis calculates I VA jua -j2e

A:

Q: ons 4.6 Lecture Example 2: The solenoid current heats rod CD from T= 30°C to Ty-180 °C. The steel…

A: given; lets take force in steel rod=Fslets take force in aluminium rod=Fal

Q: GIVE THE JOB OR OPERATION WHERE HIGH AIR HUMIDITY IS PRESENT

A: Humidity is the concentration of water vapor in the air. water vapor in the gaseous form is…

Q: Determine the equation of motion in a matrix form using Newton's second law, [m]y+ [c]y + [k]y = F.…

A: Given : To find : Equation of motion

Q: let A E. Find Conditions on a,b.c and d that AX =0o has infaitely many solution - what must there…

A:

Q: *12-40. Determine the slope at A and the deflection of end Cof the overhang beam. Take E=29(103) ksi…

A:

Q: Q2: Determine theX- and y-coordinates of the centroid of the shaded area. 20mm bomm

A:

Q: A very long rod extends horizontally from a heated wall. The rod is 20 mm in diameter and the heated…

A: Given information, Dia =20mm, Find, Heat transfer in case of infinite long rod

Q: Two tubular sections shown in Figure-2, have the same wall thickness and same circumference.…

A: Objective - To find the ratio of shear stresses for equal twisting moments for two cases.

Q: Discussion: a failure of aluminum under bending? 2- What do you expect if the bending experiment has…

A: To find :- Reasons

Q: 1. A flat plate is supplied with a constant heat flux of 100 [W/m2] from bottom. The plate has 0.5m2…

A:

Q: A flange coupling is to connect two 60mm shafts. The hubs of the coupling are 120mm, 100mm thick, &…

A: (a) the shear stress in key: 24.9655 MPa (b) the bearing stress in key: 49.9309 MPa (c) the shear…

Q: T1 -T2 = 100° ɛ = 0.8 9'rad stion cond conv

A: T∞=25°CL=0.15thickk=1.2W/mke=0.8T0=100°Ch=20W/m2K To-Find:- Inner surface temperature

Q: Griven the linear Systen 2X +3 y- z =o X - "y +5Z =0 ) Venly that X, - 1 X - and z, - -1 4 is a…

A: The linear system of equations are 2x + 3y - z = 0x - 4y + 5z = 0

Q: Two farmers are pushing on a gate with forces Fa and FB, applied at locations A and B respectively.…

A: FA= 300 Nα= 65∘β= 35∘DBC= 2mDAC= 3 m

Q: 1. A jet with a velocity V impinges a curved plate moving at velocity u in the direction of jet, as…

A:

Q: A wide-flange beam (see figure) is subjected to a shear force V. h h Using the following dimensions…

A:

Q: P5.4 A process contains a storage vat, v1, which is fed by the outflow of a vat, v2, of similar…

A: Given data : Outside diameter = 10ft Water filled           = 24ft Tensile stress         = 16000…

Q: Question 9 the dimensions of the faces of each block be 3 m by 2 m. Also, the conductivity of copper…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: brought to rest by suctessively crushing steel barrels. The length of the crash ushion is 5.0 m, and…

A:

Q: The water vapor enters a throttling valve with a mass flow rate of 2.7 kg/s, a temperature of 280 °C…

A: Given that: mass flow rate = 2.7 kg/s .Inlet conditions are: T1 = 280 oC, P1 = 30 bar Outlet…

Q: Match the following: 1. Imbalance in diesel engines 2. Vibration in machine tools 3. Blade and disk…

A: Ans : 1-c 2-e 3-a 4-d 5-b

Q: Given the image below, AB and BC are joined by a hinge in b. End A of member ASB is pin supported…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.